Rheem TRITON Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 61

background image

Ignition Control Board

Triton

Service Manual SVC1020T ; Rev 4

80 and 100 gallon chassis

5 0

LCD Display

1. Disconnect power to the water heater.
2. Remove all Molex connections to the control board.
Wires are colored and the board locations have
numbers to reconnect. See Wiring Diagram on page 8
of this document.
3. Remove the three Phillips screws holding the control
board to the top of the water.
4. Remove the control and replace in reverse order.

1.Disconnect power to the water heater.
2.Drain the water in the tank to a point below the level of
the water temp sensor.
3.Remove all wiring connections to the sensor
assembly.
4.Remove the sensor assembly with a wrench.
5.Replace in reverse order.

Disassembly and Repair

1. Disconnect power to the water heater.
2. Disconnect the three Molex connections. One goes
to the ignition control board. The other 2 pigtail to
other wiring harness.
3. Remove the two Phillips screws holding the display
assembly to the top of the water.
4. Remove the display assembly and replace in reverse
order.

Water Temperature Sensor

Blower Motor

1. Disconnect power to the water heater.
2. Disconnect the 2 Molex connections.
3. Remove the two Phillips screws holding gas valve
and venturi assembly blower motor.
4. Remove the 4 Phillips screws holding the blower the
burner mounting flange.
5. Remove the blower and gasket from the burner mounting
flange.
6. Replace parts in the reverse order making sure to use the
new gaskets supplied with the blower. (There is a gasket for
the blower/burner mounting flange and another gasket for
where the gas valve and venturi assembly meets the
blower.)

«
...
48
49
50
51
52
...
»

Содержание TRITON






























































Отзывы:

Нет отзывов

Похожие инструкции для TRITON

Бренд: TapFlo Страницы: 35

Бренд: Rainman Страницы: 17

Бренд: Valor Fires Страницы: 17

Бренд: YAMADA Страницы: 84

Бренд: Walrus Pump Страницы: 8

Бренд: Haverland Страницы: 64

Vectissimo CO180

Бренд: Rowenta Страницы: 10

Бренд: CLIVET Страницы: 7

Бренд: Kessel Страницы: 24

Бренд: Westfalia Страницы: 18

Бренд: Ulvac Страницы: 27

Бренд: ATC Страницы: 8

Бренд: Desa Страницы: 12

Бренд: Speck Страницы: 24

Бренд: Sam Страницы: 23

Powerflex PDVG-40T42

Бренд: American Water Heater Страницы: 4

Бренд: VARISCO Страницы: 18

Бренд: Comet Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды