Rheem TRITON Скачать руководство пользователя страница 5

Страница: 5 / 61

Specifications of the TRITON

Models

GHE (gas high efficiency gas) 80 and 100 gallon (tank capacity)

Powered direct vent; sealed combustion; fully condensing; ASME rating options

on all inputs; power vent options on all inputs.

Fuel Type

Natural and L.P. gas; thermal efficiency based on model

Gallon Capacity

80 and 100 gallons

Rated Gas Input (Btu/Hr.)

130,000; 150,000, 160,000’; 199,000; 250,000; 300,000; 350,000; 399,000

Ignition System

Spark ignition to main burner; no pilot of any kind

Heat Exchanger

Down fired, multi-pass heat exchanger

Diagnostics

Nonvolatile storage of heater settings and fault history. Diagnostic codes provided

through an onboard LCD display consisting of information on power to the control,

control status, fault codes and system settings.

Installation

Indoor only

Gas Connection

“ and

” NPT Female

Inlet Gas Pressure

Natural Gas Min. 3.5" w.c. Max. 10.5" w.c.

L.P. Gas Min. 11.0" w.c. Max. 13.0" w.c.

High Altitude

Units rated to 8,999ft.

Water Connection

2” NPT inlet/outlet – side connect – front and rear

1.5” for Top (Plugged from factory)

Vent Material Allowed

Polypropylene, PVC, ABS, CPVC plastic pipe options

130-160kbtu – 2” (, 3”, 4”, & 6” venting options

199kbtu – 2” (, 3”, 4”, & 6” venting options

250-399kbtu – 3”, 4” & 6” venting options

SEE USE AND CARE MANUAL

Maximum Vent Lengths

SEE USE AND CARE MANUAL

Noise Level

60 db @ 15 feet (max) using test ANSI S12.34/ISO 3744

Water Temperature

Factory Setting

120°F

Digital Thermostat (adjustable)

1 degree increments

85°F to 185°F

Temperature Differential

Factory Setting of

User selectable from 1°F to 30°F

Electrical

Electrical Rating

120 VAC 50/60Hz, 7 Amps

Wire

3 (three) wire (hot, neutral, ground)

Earth Ground Sensitive

Yes

Polarity Sensitive

Yes

Safety Devices

Temperature and Pressure Relief Valve – 150 PSI or 210

Venting Over Temperature Switch; trips at 160

F; automatic reset

Energy Cut Off for high water temperature; trips at 205

F (auto reset) +- 3

Flame Rectification - The presence of a flame is measured via a flame rod that points

into the flame. Control measures => 8.0 micro amp (uA)

Fuse protected main controller

Triton

Service Manual SVC1020T ; Rev 4

80 and 100 gallon chassis

Содержание TRITON






























































Результаты поиска

Содержание TRITON

Отзывы:

Похожие инструкции для TRITON

Бренды по названию

Популярные бренды

Rheem TRITON, Руководство по обслуживанию и тренингу

Результаты поиска

Содержание TRITON

Отзывы:

Похожие инструкции для TRITON

Бренды по названию

Популярные бренды