Rheem TRITON Скачать руководство пользователя страница 13

Страница: 13 / 61

Triton

Service Manual SVC1020T ; Rev 4

80 and 100 gallon chassis

Proof of Fan (Pressure Switch)

The PoF pressure switch confirms the blower motor is

running. Each switch is available individually.

Blocked Outlet (Pressure Switch)

The blocked outlet pressure switch is a normally closed

contact that opens with a rise in pressure. Each switch

is available individually

Blocked Inlet (Pressure Switch)

The blocked inlet pressure switch is a normally closed

contact that opens with a fall in pressure.

Each switch is available individually

Water Temperature and ECO

Probe

This probe provides the water temperature to the

controller; and also provides an energy cut off in the event

the water gets too hot (>200

F).

Lower Temperature Probe

This prove provides the lower tank temperature to the

controller.

Leak Sensor

This sensor detects water when 2.5-5mL of water is

present. It is installed in the bottom pan of the unit and

has a splash proof guard above it so tank condensation

or sprayed water will not activate it. Unit can operate

with sensor unplugged but the display will flash an

alert stating that the leak sensor is disconnected.

Factory setting for leak detection is to “Alert Only”.

Can be changed to “Disable”(Shut down the unit if a

leak is detected.)

Burner

The burner in a combustion chamber maintains a

controlled flame by giving the flame a structure to rest

on.

Parts

Содержание TRITON






























































Результаты поиска

Содержание TRITON

Отзывы:

Похожие инструкции для TRITON

Бренды по названию

Популярные бренды

Rheem TRITON, Руководство по обслуживанию и тренингу

Результаты поиска

Содержание TRITON

Отзывы:

Похожие инструкции для TRITON

Бренды по названию

Популярные бренды