Rheem TRITON Скачать руководство пользователя страница 18

Страница: 18 / 61

Status Message

Description

Water Heater

Disabled

The water heater is disabled and not in any active mode.

Standby

The water heater is in a non-active mode where the temperature of the water

in the tank is within the set point limits.

Pre- Purge

17 seconds

An initial step in a heating cycle wherein the blower is energized to clear any

potential by products of combustion from the heat exchanger.

Ignition

The ignition system and gas valve are energized during this period. Igniter

should be sparking and gas valve should be releasing fuel.

Heating

This message appears when a call for heat is present and the burner is actively

firing.

Post Purge

When the call for heat is satisfied, the gas valve is de-energized while the

blower remains energized to clear the heat exchanger.

Retry

Test failed ignition and it is retrying

Recycle

The water heater is in the 30 minute delay between retries

Fault

The water heater is experiencing a malfunction and displaying an error code

Ign. Control Comm

Error

The display is not communicating with the ignition control

1 8

Triton

Service Manual SVC1020T ; Rev 4

80 and 100 gallon chassis

Display Messages on Control Board

Содержание TRITON






























































Результаты поиска

Содержание TRITON

Отзывы:

Похожие инструкции для TRITON

Бренды по названию

Популярные бренды

Rheem TRITON, Руководство по обслуживанию и тренингу

Результаты поиска

Содержание TRITON

Отзывы:

Похожие инструкции для TRITON

Бренды по названию

Популярные бренды