Rheem TRITON Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 61

background image

Introduction

The control system for the fully condensing 80 and 100 gallon Gas High Efficiency (GHE)
Commercial Gas Water Heater is intended for use indoors. The control combines all operational
functions needed for a water heater with a powered burner system into a single printed circuit board
package. The control inputs are from a water temperature probe, pressure switches, flue gas
temperature sensor, high temperature limit switch and flame sensor. The control provides outputs for
a blower motor, spark igniter, gas valve, and has a nonvolatile storage of fault
history. The system incorporates a liquid crystal display (LCD) as the interface for the customer to
control heater function. The user interface consists of buttons for scroll through system menus,
adjustment of settings and to provide additional operational status information.

Safety

ELECTRICAL SHOCK - Troubleshooting and repairing this water heater can expose you to
electrical shock. Some of the diagnostic procedures require the presence of 120 volt AC electricity.
Use extreme caution when performing these procedures. When replacing an unserviceable
component, turn off all power to the water heater and check for the presence of power with a multi-
meter or test lamp. The ignition cable carries more than 10,000 volts of electrical energy. Use
extreme caution when diagnosing the Ultra High Efficiency Water Heater.

WATER TEMPERATURE ADJUSTMENT
Safety and energy conservation are factors to
be considered when selecting the water
temperature setting on the thermostat. Water
temperatures above 125

0

F can cause severe

burns or death from scalding. The chart shown
here may be used as a guide in determining the
proper water temperature for your application.

4

FLAMMABLE LIQUIDS AND VAPORS
Gasoline, as well as other flammable material and liquids
(adhesives, solvents, etc.), and vapors they produce are
extremely dangerous. DO NOT handle, use or store gasoline or
other flammable or combustible materials anywhere near or in
the vicinity of a water heater. The spark ignition and burner
assembly in the water heater controls can ignite these vapors.
Failure to do so can result in property damage, bodily injury or
death

Triton

Service Manual SVC1020T ; Rev 4

80 and 100 gallon chassis

«
...
2
3
4
5
6
...
»

Содержание TRITON






























































Отзывы:

Нет отзывов

Похожие инструкции для TRITON

Бренд: Kawamoto Pump Страницы: 28

Бренд: Oase Страницы: 76

Бренд: laguna Страницы: 10

Бренд: Ozito Страницы: 8

ProConnect 19B732

Бренд: Graco Страницы: 24

Бренд: WaterTech Страницы: 12

Бренд: Drummond Страницы: 12

Бренд: BSC Страницы: 28

Бренд: Eldom Страницы: 44

Бренд: red lion Страницы: 12

5.7M3/H AVEC TIMER

Бренд: YZAKI Страницы: 36

Hydroheat A650YRRTL5

Бренд: Apollo Страницы: 24

Бренд: Harbor Freight Tools Страницы: 8

Бренд: Sure Heat Manufacturing Страницы: 20

Бренд: Zoeller Страницы: 12

ROTOGEAR 3 Series

Бренд: Liquiflo Страницы: 23

Бренд: A.O. Smith Страницы: 55

Бренд: Bluegrass Living Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды