Rheem TRITON Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 61

background image

BACnet Configurations

Triton

Service Manual SVC1020T ; Rev 4

80 and 100 gallon chassis

5 9

BACnet Quick Start Guide

Note:

This water heater is compatible with

BACnet RS-485 physical layer only.

Pinout:

Pin Number

Description

1

Ground (Optional)

2

RS-485 Minus (D-)

3

RS-485 Plus (D+)

4

Common (100Ω resistor to ground)

Instructions:

1. Wire up the BACnet connections per the given pinout
2. Plug in the connector to the heater as shown. The connector plugs in to the top, green connector to the left
of the display. When connected properly, the screws will face the back of the water heater, and pin 4 will be
to the top.
3. After connecting, select “Settings” and, then, “bacnet” on the display to modify the BACnet settings. See the
below details on configuring the BACnet settings.

BACnet Settings Details:

BACnet Setting

Default
Value

Additional Information

BACnet MAC Address

1

Range: 0 to 127 for MS/TP Master and 0 to 254 for MS/TP Slave
When possible, 0 should be avoided.
Must be unique among all devices on a given BACnet network
segment.

BACnet Baud Rate

38.4 kbps

kbps: kilo-bits per second
Options: 9.6 kbps, 19.2 kbps, 38.4 kbps, 57.6 kbps, 76.8 kbps, or
115.2 kbps

BACnet Config

MS/TP
Master

Options: MS/TP Master or MS/TP Slave

BACnet Max Master Address

127

Only applicable if BACnet Config is set to MS/TP Master.
Range: 0 through 127

BACnet Device Instance

4,194,303

Range: 0 through 4,194,303
The default value indicates unassigned instance, and should not
be used. Instance must be assigned for use.
Must be unique across devices on all BACnet network segments
of the BACnet internetwork.

«
...
57
58
59
60
61
»

Содержание TRITON






























































Отзывы:

Нет отзывов

Похожие инструкции для TRITON

Бренд: Ultranatura Страницы: 24

Бренд: Danfoss Страницы: 26

Бренд: Calpeda Страницы: 80

Бренд: Atlas Copco Страницы: 137

Бренд: A.O. Smith Страницы: 119

jumbo floodfighter

Бренд: Davey Страницы: 8

Бренд: Wacker Neuson Страницы: 72

Бренд: WilTec Страницы: 8

Бренд: Nagman Страницы: 15

Бренд: Pattfield Ergo Tools Страницы: 52

Бренд: Calpeda Страницы: 19

Бренд: Serenity Страницы: 3

Бренд: HP SCHOU Страницы: 84

Бренд: Fakir Страницы: 44

Бренд: Pfeiffer Vacuum Страницы: 60

Бренд: Wanner Engineering Страницы: 24

Бренд: Navien Страницы: 60

ProSeries Chem-Feed CFPS-1

Бренд: Blue-White industries Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды