Renesas H8S Family страница 778 Скачать руководство пользователя | Manualshive

Страница: 778 / 1230

background image

Section 19 LPC Interface (LPC)

Rev. 1.00 Mar. 12, 2008 Page 730 of 1178

REJ09B0403-0100

19.3.30 BT Data Buffer (BTDTR)

BTDTR is used to implement the BT mode. BTDTR consists of two FIFOs: the host write transfer
FIFO and the host read transfer FIFO. Their capacities are 64 bytes each. When using BTDTR,
enable FIFO by means of the bits FSEL0 and FSEL1.

R/W

Bit Bit

Name

Initial
Value Slave Host

Description

7 to 0 bit7 to bit0 Undefined R/W

R/W

The data written by the host is stored in FIFO (64
bytes) for host write transfer and read out by the
slave in order of host writing. The data written by the
slave is stored in FIFO (64 bytes) for host read
transfer and read out by the host in order of slave
writing.

19.3.31 BT Interrupt Mask Register (BTIMSR)

BTIMSR is one of the registers used to implement BT mode. The BTIMSR register contains the
bits used to control the interrupts to the host.

R/W

Bit Bit

Name

Initial
Value Slave Host Description

7 BMC_

HWRST

0 R/(W)

*

2

R/(W)

*

1

Slave Reset

Performs a reset from the host to the slave. The
host can only write a 1. Writing a 0 to this bit is
invalid. The host will always return a 0 on read
out. Setting the RSTRENBL bit enables a 1 to be
read from the host.

0: The reset is cancelled

[Clearing condition]

When the slave writes a 0, after a 1 has been
read from BMC_HWRST.

1: The reset is in progress.

[Setting condition]

When the host writes a 1.

6

5





0

0

R/W

R/W

R/W

R/W

Reserved

«
...
776
777
778
779
780
...
»

Содержание H8S Family















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для H8S Family

PCMCIA WIRELESS ASAPTER DWL-650

Бренд: D-Link Страницы: 5

PowerLine DHP-W611AV

Бренд: D-Link Страницы: 78

Бренд: XMG Страницы: 5

Бренд: NAD Страницы: 2

Бренд: 3Com Страницы: 2

Бренд: 3Com Страницы: 74

Бренд: 3Com Страницы: 6

Бренд: Udoo Страницы: 7

Бренд: Octavo Страницы: 28

Бренд: Obihai Страницы: 2

Бренд: Industrex Страницы: 51

PowerBeam AC Gen2

Бренд: Ubiquiti Страницы: 22

Бренд: Telex Communications Страницы: 28

Бренд: Seattle Computer Products Страницы: 31

EZ-Extender Analog 120-Pin Probing Board

Бренд: Analog Devices Страницы: 29

Seven Solutions WR-ZEN Series

Бренд: Orolia Страницы: 167

Бренд: FDI Страницы: 2

Бренд: H3C Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды