manualshive.com logo in svg

Renesas 89HPES24T3G2ZBAL, Руководство пользователя

Поделиться
Скачать
Renesas 89HPES24T3G2ZBAL Скачать руководство пользователя страница 110

IDT   Configuration Registers

PES24T3G2 User Manual

8 - 28

February 22, 2012

Notes

PCIESCAP - PCI Express Slot Capabilities (0x054)

13

DLLLA

RO

0x0

Data Link Layer Link Active. This bit indicates the status for the 
data link control and management state machine.
0x0 - (not_active) Data link layer not active state
0x1 - (active) Data link layer active state
This bit must never be set by hardware if the DLLLA bit in the 
PCIELCAP register is cleared.

14

LBWSTS

RW1C

0x0

Link Bandwidth Management Status. This bit is set to indicate 
that either of the following have occurred without the link transi-
tioning through the DL_Down state.
A link retraining initiated by setting the LRET bit in the PCIELCTL 
register has completed.
The PHY has autonomously changed link speed or width to 
attempt to correct unreliable link operation either through an 
LTSSM time-out or a higher level process.
This bit must be set if the Physical Layer reports a speed or width 
change was initiated by the downstream component that was not 
indicated as an autonomous change.
If the LBN field in the PCIELCAP register is cleared, this field is 
hardwired to zero. 
This field is hardwired to zero in the upstream port.

15

LABWSTS

RW1C

0x0

Link Autonomous Bandwidth Status. This bit is set to indicate 
that either that the PHY has autonomously changed link speed or 
width for reasons other than to attempt to correct unreliable link 
operation.
This bit must be set if the Physical Layer reports a speed or width 
change was initiated by the downstream component that was 
indicated as an autonomous change.
If the LBN field in the PCIELCAP register is cleared, this field is 
hardwired to zero.
This field is hardwired to zero in the upstream port.

Bit 

Field

Field

Name

Type

Default

Value

Description

0

ABP

RWL

0x0

Attention Button Present. This bit is set when the Attention But-
ton is implemented for the port.
This bit is read-only and has a value of zero when the SLOT bit in 
the PCIECAP register is cleared.

1

PCP

RWL

0x0

Power Control Present. This bit is set when a Power Controller 
is implemented for the port.
This bit is read-only and has a value of zero when the SLOT bit in 
the PCIECAP register is cleared.

2

MRLP

RWL

0x0

MRL Sensor Present. This bit is set when an MRL Sensor is 
implemented for the port.
This bit is read-only and has a value of zero when the SLOT bit in 
the PCIECAP register is cleared.

Bit 

Field

Field

Name

Type

Default

Value

Description

Содержание 89HPES24T3G2ZBAL






































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды