REI TALAN 3.0 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 82

background image

5

Revision 3.01

© COPYRIGHT RESEARCH ELECTRONICS INTERNATIONAL

REI products are designed and intended for legal commercial applications, however because
laws and regulations vary from state to state and country to country, it is the sole responsibility
of the purchaser and user/operator to check and comply with all applicable laws and
regulations for the possession and operation of this equipment before and after making a
purchase.

This manual contains proprietary information intended solely for use with the TALAN
Telephone and Line Analyzer.

Information contained in this manual including product operation and specifications is subject
to change without notice.

Any product or brand names contained in this manual are used only for identification purposes
and are trademarks or registered trademarks of their respective holders.

NOTE: The overall effectiveness of any technical surveillance countermeasure is directly
dependent on the level of threat and the user’s ability to properly deploy the appropriate
countermeasure. REI’s Center for Technical Security offers training on technical surveillance
countermeasure equipment.

OWNER’S RECORD

The Serial Number of each TALAN is located on the underside of the unit. Please record this
number and refer to it whenever you contact your dealer or Research Electronics International
concerning this product. Note: Removal or alteration of the serial number automatically voids
all warranties of this product.

MODEL: TALAN

SERIAL NUMBER: __________________

Research Electronics International, LLC

455 Security Drive, Cookeville, TN 38506 U.S.A.

(800) 824-3190 (US Only)

•

+1 931-537-6032

www.reiusa.net

© Copyright Research Electronics International LLC

«
...
3
4
5
6
7
...
»

Содержание TALAN 3.0



















































































Отзывы:

Нет отзывов

Похожие инструкции для TALAN 3.0

A300 Sport.Tool

Бренд: Navman Страницы: 1

Бренд: Tavool Страницы: 12

Бренд: Hilti Страницы: 31

Бренд: Hanna Instruments Страницы: 2

Бренд: Zero 88 Страницы: 32

Бренд: Alpes Lasers Страницы: 41

Бренд: Thermo Scientific Страницы: 56

Бренд: Velleman Страницы: 15

Бренд: East Tester Страницы: 36

Proline Promass 200

Бренд: Endress+Hauser Страницы: 12

Proline Promag W 400

Бренд: Endress+Hauser Страницы: 64

MRG 512 PQ Flex

Бренд: janitza Страницы: 9

Бренд: LOVATO ELECTRIC Страницы: 9

Бренд: National Instruments Страницы: 40

Бренд: Hioki Страницы: 16

Pianovelle GRP3

Бренд: Baldwin Страницы: 34

Бренд: Topcon Страницы: 2

Бренд: Aventics Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды