REI TALAN 3.0 Скачать руководство пользователя страница 22

Страница: 22 / 82

TESTING CONCEPTS AND RECOMMENDED TEST SEQUENCE

Automated Sequencing and Manual Operation

The TALAN has many test functions that can be performed in either an

Automated Sequence

Mode

Manual Mode

. The main difference is that the

Automated Sequence Mode

is designed

to walk the user through the previously recommended test sequence while the

Manual Mode

designed to allow the user to go to any specific tests and completely control the parameters
and conditions of the tests.

Manual Mode

is most useful for testing for specific items of interest

while the

Automated Sequencing

is recommended for a complete evaluation of the line. In both

modes, the testing screens are very similar; however, the

Automated Sequencing Mode

test

screens have a

green

background while the

Manual Mode

test screens have a

brown

background.

This section will describe how to utilize the

Sequence

mode. However, the details of the actual

tests being performed will be described later as

Manual

Tests functions.

Содержание TALAN 3.0



















































































Результаты поиска

Содержание TALAN 3.0

Отзывы:

Похожие инструкции для TALAN 3.0

Бренды по названию

Популярные бренды

REI TALAN 3.0, Руководство пользователя

Результаты поиска

Содержание TALAN 3.0

Отзывы:

Похожие инструкции для TALAN 3.0

Бренды по названию

Популярные бренды