REI TALAN 3.0 Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 82

background image

TALAN SPECIFICATIONS

82

TALAN SPECIFICATIONS

CONTROL SYSTEM

Primary Computer: 32 bit RISC processor, 520 MHz
Internal Memory: 64 MB SDRAM (OS), 64 MB Flash
External Memory: Compact Flash Type III,
USB mass storage

DIGITAL I/O

Network: 10/100 Ethernet Controller for IP Packet
Detection
USB: USB Device (A Type) supports external
keyboard, mouse, and USB mass storage device; USB
Host (B type) for future use.

ANALOG I/O

Headphone Output: 3.5 mm connector
Microphone Input: 3.5 mm input

USER INTERFACE

Hard Keys: 6 Soft Menu Keys, 5 Button Quadrant
Navigation & other dedicated keys
Encoder: High-Resolution Optical Encoder
Integrated Touch Screen with Stylus
Test Inputs:
Dual MOD8:

Supports 2, 4, 6, & 8 wire
Modular Phone Jacks with Shield
(With TALAN 3.0)

Banana Type:

Standard sleeved sockets:

Ring, Tip, and Earth

SMB RF Input:

RF/Antenna Connection to

8 GHz Broadband Detector

Expansion Port: Supports communication

and measurement for use
with future accessories

All Inputs Electrically Isolated

RF SYSTEM

Spectrum Analyzer:
Dual Conversion, Super-Heterodyne Receiver
Frequency Range: 30 kHz to 85 MHz
Sweep Time: 2 Seconds
Step Size: 1 kHz
Bandwidth: 18 kHz
Sensitivity: -100 dBm

Broadband Detector:
RF SMB Input: 100 kHz to 8 GHz
Line Level Test: 100 kHz to 600 MHz
Sensitivity: -65 dBm

DIGITAL MULTIMETER

Quick Response Auto-Ranging: 500msec Sample Rate
AC/DC Volts: 0 to 250V Maximum
AC/DC Current: 0 to 300mA Maximum
Resistance: 0 to 42MΩ
Capacitance: 50pF to 40µF

BIAS GENERATOR

Optically Isolated, Direct Digital Control: High voltage
DAC
Output Ceiling: ±80V
Output Ceiling (Shield): ±65VDC, ±33VAC
Modulation: Fixed voltage, or variable rate Sine
wave (10 Hz – 300 Hz)

AUDIO

Audio Bandwidth: 20 Hz – 20 kHz
Gain: Up to 80 dB total system gain
AGC: Digitally Controlled Automatic Gain
Filter: Analog Voice band filter (300 Hz to 3 kHz)

POWER SYSTEM

External Input: 15VDC @3A
Universal Power Supply: 100-240VAC, 50-60Hz
Removable Battery: Rechargeable Lithium ion,
4-hour runtime (typical)

MECHANICAL

Dimensions: 10.0 in x 12.9 in x 2.7 in
(25.4 cm x 32.8 cm x 6.9 cm)
Weight with Battery: 6 lbs (2.7 kg)
Case Dimensions: 5.4 in x 14.9 in x 19.5 in
(13.7 cm x 37.8 cm x 49.5 cm)
Loaded Case Weight: 19.0 lbs (7.1 kg)
Operating Temperature: 0°C to +50°C

HARMONIC LOCATOR PROBE

Operational Frequency: 225 kHz & 450 kHz
Antenna Type: Balanced Loopstick
Headphone Audio Output: 16Ω, 105dB SPL limited
Battery: 9V Alkaline
Run-Time: 10 hours average, 22 hours (headphones)
Size: 17.5 in x 1.5 in (44.45 cm x 3.8 cm) stored
63.75 in x 1.5 in (162 cm x 3.8 cm) fully extended
Weight: 1 lbs (.5 kg)

«
...
80
81
82

Содержание TALAN 3.0



















































































Отзывы:

Нет отзывов

Похожие инструкции для TALAN 3.0

Бренд: A&D Страницы: 102

Бренд: Ulvac Страницы: 24

Бренд: Kawai Страницы: 64

Бренд: Kawai Страницы: 28

Бренд: Kawai Страницы: 28

Бренд: Dwyer Instruments Страницы: 189

Бренд: Lowrey Страницы: 109

Бренд: UEi Страницы: 5

miniSERIES Series

Бренд: Valeport Страницы: 25

Seeker 400 Series

Бренд: General Страницы: 24

Бренд: shelyak Страницы: 45

Бренд: Clavia Страницы: 13

Бренд: RS PRO Страницы: 41

Бренд: Sage Страницы: 75

AS-i CompactModule M8

Бренд: IFM Страницы: 4

Бренд: THE ELECTRON MACHINE CORPORATION Страницы: 32

Бренд: Vanguard Instruments Company Страницы: 111

Бренд: Hanna Instruments Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды