manualshive.com logo in svg

RCT Power Storage DC 10.0, Руководство пользователя

Поделиться
Скачать
RCT Power Storage DC 10.0 Скачать руководство пользователя страница 115

110 

AFI_300mA 

current. 
Inverter stops feeding. 

IDC 

IDC_SLOW 

Your power storage continually monitors 
the quality of current fed in. 
If an increased DC-component in AC-
current is detected, inverter stops feeding. 

Restart the Power Storage. 
If the error still occurs, please contact 
service. 

CAN_TIMEOUT 

CAN communication timeout with battery. 

Restart the power storage and reestab-
lish the CAN connection. 

RELAYS TEST 

Before connection to grid, your power 
storage checks the operation of mains 
relays. An error was detected during this 
check. 

Restart the Power Storage 
If the error still occurs, please contact 
service. 

EXT_OFF 

Your power storage has the possibility to 

be switched off by a configurable “emer-
gency stop”. This signal is active and in-

verter stops feeding. 

Check “emergency stop” switch to be 

unlocked. 

Check configuration of “emergency 
stop” function in APP.

 

RS485_POWER_SW 

Error by RS485 communication with the 
Power Switch. 

Check the RS485 connector fitting. 
Check the RS485 connector wire ring . 
If the error still occurs, please contact 
service. 

TEMP_SINK1 

Your power storage is designed to feed full 
power up to an ambient temperature of 
+40°C.  
If heatsink temperatures exceed a specific 
threshold inverter reduces power. 

Check ambient temperature of installa-
tion, clean the heatsink of inverter. 
Observe the installation distances spec-
ified in manual. 
Remove possible objects laying on the 
convection paths of heatsink. 

TEMP_HIGH 

Your power storage is designed to feed full 
power up to an ambient temperature of 
+40°C. 
 If heatsink temperature exceeds a specific 
threshold inverter stops feeding.  
After the heatsink temperature drops, 
inverter restarts feeding. 

Check ambient temperature of installa-
tion. 
Clean the heatsink of inverter. 
Observe the installation distances spec-
ified in manual. 
Remove possible objects laying on the 
convection paths of heatsink. 

TEMP_BAT 

Your power storage is designed to feed full 
power up to an ambient temperature of 
+40°C. 
The charge/discharge current will be re-
duced. 
If heatsink temperature exceeds the bat-
tery will be disconnected. 

Check ambient temperature of installa-
tion. 
Clean the heatsink of inverter. 
Observe the installation distances spec-
ified in manual. 
Remove possible objects laying on the 
convection paths of heatsink. 

Содержание Power Storage DC 10.0























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды