RCH Touch ME Скачать руководство пользователя страница 31

Страница: 31 / 62

RCH

INSTALLATION AND MAINTENANCE MANUAL model TOUCH ME

- 31 -

4.3.2 SELECTING THE KEYPAD DISPLAY

TOUCH ME lets you choose between three basic keypad display configurations to suit
operational requirements.
The

VIDEO 1

configuration is selected by default (see section 3.1).

To select the VIDEO 2 or VIDEO 3 display configurations, proceed as follows:

A. In the

ASPECT

screen, press one of the keys [CONF. VIDEO 1], [CONF.

VIDEO 2] or [CONF. VIDEO 3].

B. The chosen configuration is displayed in the white window.
C. To activate the chosen configuration, press

D. The message PLEASE SWITCH OFF-ON appears.

Switch the cash register off at the switch on the left side near the keypad
display.

Wait a few seconds and switch back on again.

The new configuration appears as soon as the system restarts.

IMPORTANT NOTE:

The currently selected configuration remains active until changed. To

select anther configuration, repeat the procedure given above from step A, or restore the
keypad display to its default configuration (see section 3.5).

4.3.3 SELECTING LANGUAGE

The

ASPECT

screen also contains the two keys

ITA

and

ENG

. Press these to select the

corresponding language for use by the cash register.

ITA

= Italian

ENG

= English

When you press a key, the relevant language is selected instantly.

Содержание Touch ME































































Результаты поиска

Содержание Touch ME

Отзывы:

Похожие инструкции для Touch ME

Бренды по названию

Популярные бренды

RCH Touch ME, Руководство по установке и обслуживанию

Результаты поиска

Содержание Touch ME

Отзывы:

Похожие инструкции для Touch ME

Бренды по названию

Популярные бренды