Raven RS Lite Скачать руководство пользователя страница 97

Страница: 97 / 125

016-4010-001 Rev. J

SLINGSHOT

• Touch the refresh button in the lower, left corner to update the list of available WiFi networks.
• Select an available network to enter the WiFi password and connect to the selected network. The network to

which the system is currently connected will display with a green check mark on the WiFi Connection Status

page.

MANUAL HOTSPOT

Select Manual Hotspot to broadcast a hotspot for local WiFi devices.

RAVEN AUTO

Select Raven Auto to allow the system to automatically select the best WiFi network connection. To change which

WiFi network the system is connected to, select the Manual Client mode.

NOTE:

When set to Raven Auto, a small “A” indicator will be displayed to indicate Raven is controlling the

Hotspot and WiFi settings for the system.

FIGURE 14. WiFi Connection Status

RTK SOURCE SETTINGS

FIGURE 15. RTK Source Page

Содержание RS Lite





























































































































Результаты поиска

Содержание RS Lite

Отзывы:

Raven RS Lite, Руководство по калибровке и эксплуатации, Страница: 97 / 125

Результаты поиска

Содержание RS Lite

Отзывы: