Raven RS Lite Скачать руководство пользователя страница 51

Страница: 51 / 125

016-4010-001 Rev. J

GPS CONFIGURATION

POSITION ACCURACY SETUP

FIGURE 4. GPS Status Information Setup Page

Status.

Displays the status of the GNSS solution. Statuses that may be displayed in this area include:

• No Signal
• Error
• Converging
• Converged

Current Accuracy.

Value displayed is the horizontal standard deviation reported by the GPS receiver.

Accuracy Threshold.

This value dictates the distance from which the machine GPS position may deviate from the

Current Accuracy position. If the GPS solution falls outside the set Accuracy Threshold, a DTC entry will displayed

into the Diagnostic Trouble Code page. The Accuracy Threshold will be populated with a default value.

TERRAIN COMPENSATION SETUP

FIGURE 5. Terrain Compensation Setup Page

Roll, Pitch, Yaw Rate, and Heading.

Real-time measurement data used by the 3D terrain compensation feature.

Calibrate Terrain Compensation.

Begins the terrain compensation process.

Содержание RS Lite





























































































































Результаты поиска

Содержание RS Lite

Отзывы:

Raven RS Lite, Руководство по калибровке и эксплуатации, Страница: 51 / 125

Результаты поиска

Содержание RS Lite

Отзывы: