Raven RS Lite Скачать руководство пользователя страница 29

Страница: 29 / 125

016-4010-001 Rev. J

CALIBRATION - HDU-SPECIFIC, MD, AND STEERING-READY

NOTE:

To ensure the calibration is successful, the number of starts and stops during the calibration process

should be limited. If it is necessary to pause the calibration process, turn the steering wheel or press

the Stop button on the field computer. Tap the foot/enable switch again to resume calibration.

NOTE:

During calibration, the machine will make several hard left and right turns. Adjust the vehicle speed

and location as necessary.

NOTE:

If an error message is displayed during calibration, refer to

Diagnostic Trouble Codes (DTC)

section on

page 58 for possible causes and corrective action steps to be taken.

1. Park the machine on a level surface with several acres of smooth ground available.

FIGURE 26. Steering Control Calibration Page

2. Drive forward at 1.6 - 6.4 km/h [1 - 4 mph].
3. Press the resume switch or use the on-screen arrow to begin calibration. The following pages will be displayed

during the process:

WARNING

During the auto-steering calibration, the machine

will make several hard left and right turns. Adjust

the vehicle speed and location as necessary.

Содержание RS Lite





























































































































Результаты поиска

Содержание RS Lite

Отзывы:

Бренды по названию

Популярные бренды

Raven RS Lite, Руководство по калибровке и эксплуатации

Результаты поиска

Содержание RS Lite

Отзывы:

Бренды по названию

Популярные бренды