manualshive.com logo in svg

Raven RS Lite, Руководство по калибровке и эксплуатации

Поделиться
Скачать
Raven RS Lite Скачать руководство пользователя страница 36

C

HAPTER

 6

30

Raven RS1™ and RS Lite™ Calibration and Operation Manual

ADVANCED TUNING

FIGURE 2. Advanced Tuning Menu

Position Gain. 

Determines how aggressively the RS1 system responds to an off-track error. A higher Position Gain 

value results in a more aggressive response to an off-track error, while a lower value indicates a less aggressive 

response.

Heading Gain. 

Determines how aggressively the RS1 system responds to a heading error. A higher Heading Gain 

value results in a more aggressive response to a heading error, while a lower value indicates a less aggressive 

response.

Yaw Rate Gain. 

Determines the impact of the yaw rate on tracking performance. A higher Yaw Rate Gain value 

results in a more aggressive response to yaw rate, while a lower value results in a less aggressive response.

Integral Gain. 

This value corrects long-term errors in the wheel control. If the system is not achieving the desired 

wheel angle during operation, the system will re-direct the wheels to the desired set point. This value is generally 

at or near zero.

Yaw Error Compensation. 

Increase the yaw error compensation value to allow the machine steer more 

aggressively on curves.

Terrace Mode. 

Select the terrace mode check box to enable Terrace Mode. This mode temporarily adjusts some 

configuration settings to increase performance on terraced fields.

Содержание RS Lite






























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды