Raven RS Lite Скачать руководство пользователя страница 33

Страница: 33 / 125

CHAPTER

016-4010-001 Rev. J

CHAPTER 5

MACHINE SETTINGS

FIGURE 1. Machine Settings Page

The Machine Settings page provides access to the machine tunesets and configurations which were entered

during the initial system calibration.

FIGURE 2. Machine Configuration Page

• The Change Profile button allows the user to select an existing tuneset or create a new machine tuneset.
• The Machine Configuration Information button allows the operator to view the profile which was entered

during the calibration process. Settings cannot be changed unless the RS1 system is recalibrated. Press the

Accept button in the lower-right corner of the page to return to the Machine Settings page.

• The Machine Offsets Setup button allows the user to view and adjust the following:

Содержание RS Lite





























































































































Результаты поиска

Содержание RS Lite

Отзывы:

Бренды по названию

Популярные бренды

Raven RS Lite, Руководство по калибровке и эксплуатации

Результаты поиска

Содержание RS Lite

Отзывы:

Бренды по названию

Популярные бренды