Raven RS Lite Скачать руководство пользователя страница 18

Страница: 18 / 125

HAPTER

Raven RS1™ and RS Lite™ Calibration and Operation Manual

GPS CALIBRATION

FIGURE 3. Machine Selection Page

1. Select the Machine Type, Machine Make, and Machine Model from the Machine Selection drop-down boxes.
2. Select the

Next

arrow.

3. Use the drop-down list to select one of the following options for devices installed on a OMNi system.

FIGURE 4. OMNi System Enable Page

NOTE:

The OMNiDRIVE™ System page will only display when calibrating an RS Lite with a compatible tractor

or any combine machine type.

GPS Only.

Stream GNSS correction information only. Select this option for guidance only applications or to stream

corrections to a separate automated steering system.

Steering Only.

Use the guidance and automated steering features of the device. Select this option for automated

tractor or sprayer steering applications.

Autonomy Driverless.

Select this option to enable features for autonomous systems such as OMNiDRIVE.

System

Information

DTC

Feature

Unlocks

Machine Test

Содержание RS Lite





























































































































Результаты поиска

Содержание RS Lite

Отзывы:

Похожие инструкции для RS Lite

Бренды по названию

Популярные бренды

Raven RS Lite, Руководство по калибровке и эксплуатации

Результаты поиска

Содержание RS Lite

Отзывы:

Похожие инструкции для RS Lite

Бренды по названию

Популярные бренды