Raven RS Lite Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 125

background image

016-4010-001 Rev. J

33

STEERING SETUP

FIGURE 6. PWM Table Page

WHEEL CONTROL CALIBRATION

FIGURE 7. Wheel Control Calibration Page

NOTE:

The Wheel Control Calibration allows the machine hydraulic system to be calibrated separately from

the complete RS1 system calibration.

The steering control calibration process

allows the RS1 to learn the hydraulic capabilities of the machine for

optimal steering performance in the field.

Before beginning the machine steering system calibration, ensure that the following conditions are met:
• The booms are racked on self-propelled units.
• There are no implements connected to the hitch.
• The machine engine is running at the normal operating RPM.
• The machine measurements are correctly entered into the field computer.

«
...
37
38
39
40
41
...
»

Содержание RS Lite






























































































































Отзывы:

Нет отзывов

Похожие инструкции для RS Lite

Бренд: ICS Schneider Messtechnik Страницы: 124

Бренд: Taylor Made Страницы: 2

Бренд: York Fitness Страницы: 18

Бренд: Safco Страницы: 2

Бренд: Omni Страницы: 193

Бренд: MacDon Страницы: 272

Бренд: MacDon Страницы: 70

Бренд: Kawai Страницы: 10

Бренд: Nectar Страницы: 46

Бренд: Neauvia Страницы: 17

Бренд: Qlight Страницы: 4

Бренд: Parkside Страницы: 95

Бренд: Safety 1st Страницы: 4

Бренд: Safety Engineering Страницы: 5

Бренд: Yamaha Страницы: 4

Бренд: Wacker Neuson Страницы: 120

Бренд: Gardco Страницы: 17

Бренд: H&S Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды