Raven RS Lite Скачать руководство пользователя страница 95

Страница: 95 / 125

016-4010-001 Rev. J

SLINGSHOT

FIGURE 10. Cellular Configuration Pages

Country.

Displays the country, chosen by the user, of the cellular provider. Can be changed by the user.

Network Provider.

Displays the cellular network provider, chosen by the user. The setting can be changed on this

page.

Cellular APN.

Displays the cellular APN in use. The network can be selected from the drop down or defined by

the user.

APN Username and Password.

Displays the APN Username and Password, when applicable. This is only used by

some providers and must be given by such providers.

ETHERNET SETTINGS

FIGURE 11. Ethernet Settings Page

There are two selectable modes for the Ethernet connection in the RS1 unit.

Raven Field Computer (Server Mode).

Select this mode when the RS1 unit is directly connected to the field

computer via an Ethernet cable.

Field Hub (Client Mode).

Select this mode when the RS1 unit is directly connected to the field hub via an Ethernet

cable.

Disabled.

Select this option to disable Ethernet.

Содержание RS Lite





























































































































Результаты поиска

Содержание RS Lite

Отзывы:

Бренды по названию

Популярные бренды

Raven RS Lite, Руководство по калибровке и эксплуатации

Результаты поиска

Содержание RS Lite

Отзывы:

Бренды по названию

Популярные бренды