Raven RS Lite Скачать руководство пользователя страница 40

Страница: 40 / 125

HAPTER

Raven RS1™ and RS Lite™ Calibration and Operation Manual

• The machine hydraulic fluid is at the normal operating temperature.

NOTE:

To ensure the calibration is successful, the number of starts and stops during the calibration process

should be limited. If it is necessary to pause the calibration process, turn the steering wheel or press

the

Stop

button on the field computer. Tap the foot/enable switch again to resume calibration.

NOTE:

During calibration, the machine will make several hard left and right turns. Adjust the vehicle speed

and location as necessary.

NOTE:

If an error message is displayed during calibration, refer to Chapter 10,

Diagnostics and

Troubleshooting

on page 53 for possible causes and corrective action steps to be taken.

1. Park the machine on a level surface with several acres of smooth ground available.

WARNING

The machine will steer automatically. While

calibrating or operating the RS1 system, be sure

the area around the vehicle is clear of people and

obstacles before engaging the steering system.

To disengage auto-steering at any time, turn the

steering wheel or select the on-screen Stop

button.

NOTICE

The calibration of the machine steering system

should be performed in a field or other large,

open space and during conditions similar to

normal vehicle operation.

If the ground or surface is slippery, muddy, or

freshly tilled, the RS1 system may learn incorrect

steering responses for normal operating

conditions.

Ensure the machine hydraulics are operating

properly and there are no other mechanical

issues that may affect the performance of the RS1

system.

Содержание RS Lite





























































































































Результаты поиска

Содержание RS Lite

Отзывы:

Похожие инструкции для RS Lite

Бренды по названию

Популярные бренды

Raven RS Lite, Руководство по калибровке и эксплуатации

Результаты поиска

Содержание RS Lite

Отзывы:

Похожие инструкции для RS Lite

Бренды по названию

Популярные бренды