Raven RS Lite Скачать руководство пользователя страница 57

Страница: 57 / 125

CHAPTER

016-4010-001 Rev. J

CHAPTER 9

ROUTINE OPERATION

WIDGET DEFINITIONS

The following are common status or mode information which may be displayed in the RS1 system while in a job:

NOTE:

Refer to

Diagnostic Trouble Codes (DTC)

section on page 58 for additional status conditions which

may be displayed in the RS1 or RS Lite on-screen widget.

UT NAVIGATION BUTTONS

ROS

CRX

Message

The RS1 is detected, but the operator must accept

responsibility for the operation of the RS1 system.

No A-B path or guidance line has been set or an

active DTC is preventing the RS1 system from

engaging.

RS1 is detected, turned on, and calibrated.

RS1 is detected and in operation.

Vehicle speed is too fast or too slow for RS1

operation and the system will disengage.

Accept

- Saves the changes made to the system at the end of the setup process

and returns the to the Tools Menu.

Next

- Saves the changes made to the system and proceeds to the next step in

the setup process.

Previous

- Returns to the previous page in the setup process.

Содержание RS Lite





























































































































Результаты поиска

Содержание RS Lite

Отзывы:

Raven RS Lite, Руководство по калибровке и эксплуатации, Страница: 57 / 125

Результаты поиска

Содержание RS Lite

Отзывы: