Raven RS Lite Скачать руководство пользователя страница 68

Страница: 68 / 125

HAPTER

Raven RS1™ and RS Lite™ Calibration and Operation Manual

168

High voltage.

Check battery voltage.

Low voltage.

621

.11

GPS receiver error: LNA

failure.

Cycle power to the RS1.

.31

GPS receiver error:

Antenna power.

GPS receiver error:

Antenna shorted.

GPS receiver error:

Antenna open.

628

.13

Memory error.

1. Cycle power to the RS1.

2. If the error persists, contact your local Raven dealer

or the Raven Technical Service team.

630

.13

System not calibrated.

Complete the initial calibration wizard to use RS1.

Review Chapter 3,

Calibration - HDU-Specific, MD, and

Steering-Ready

, for additional assistance.

.31

Steering calibration

recommended.

Complete a steering control calibration. Review the

Steering Calibration

section on page 19 for additional

assistance.

701

Resume switch stuck on.

1. Check the resume switch functionality in the RS1 UT.
2. Check the resume switch cabling and connections.

841

GPS not converged.

1. Wait for GNSS to converge (up to 30 minutes).
2. Cycle power to the RS1.

.11

GPS error.

1. Ensure the RS1 is calibrated and the desired

differential source is unlocked.

2. Wait for GNSS to converge (up to 10 minutes).
3. Ensure that NMEA 2000 is selected. Review the

Chapter 7,

GPS Configuration

.15

Poor GPS position

accuracy.

1. If using Satellite GS or RTK corrections, ensure that

the GNSS quality is as expected for those correction

sources. Review the

GPS Status

section on page 57.

2. Adjust the position accuracy to allow greater

tolerance for the current GNSS position accuracy.

1504

Operator not present.

1. Check presence switch cabling and connections.
2. Confirm presence switch functionality in the RS1 UT.
3. Choose activity monitor.

2901

Incompatible hardware.

A machine specific tuneset has not been developed for

combination of machine type and valve type. Select a

generic machine type and recalibrate the RS1.

3045

.31

Authorization denied.

Check the steering control unit (SCU) cabling is properly

connected. Check connections for pins which are not

making proper connection (e.g. bent or pushed in).

Code ID

Description

Recommended Actions

Содержание RS Lite





























































































































Результаты поиска

Содержание RS Lite

Отзывы:

Похожие инструкции для RS Lite

Бренды по названию

Популярные бренды

Raven RS Lite, Руководство по калибровке и эксплуатации

Результаты поиска

Содержание RS Lite

Отзывы:

Похожие инструкции для RS Lite

Бренды по названию

Популярные бренды