Raven RS Lite Скачать руководство пользователя страница 15

Страница: 15 / 125

CHAPTER

016-4010-001 Rev. J

CHAPTER 3

CALIBRATION - HDU-SPECIFIC,

MD, AND STEERING-READY

WARNING

The machine will steer automatically. While

calibrating or operating the RS1 steering system,

be sure the area around the vehicle is clear of

people and obstacles before engaging the

steering system.

To disengage auto-steering at any time, turn the

steering wheel or select the on-screen Stop

button.

WARNING

During the auto-steering calibration, the machine

will make several hard left and right turns. Adjust

the vehicle speed and location as necessary.

NOTICE

Calibration of the machine steering system

should be performed in a field or other large,

open space and with conditions similar to normal

vehicle operation.

If the ground or surface is slippery, muddy, or

freshly tilled, the RS1 steering system may learn

incorrect steering responses for normal

operating conditions.

Ensure the machine hydraulics are operating

properly and there are no other mechanical

issues that may affect the performance of the RS1

steering system.

Содержание RS Lite





























































































































Результаты поиска

Содержание RS Lite

Отзывы:

Бренды по названию

Популярные бренды

Raven RS Lite, Руководство по калибровке и эксплуатации

Результаты поиска

Содержание RS Lite

Отзывы:

Бренды по названию

Популярные бренды