6
PROGRAMMING
The Ranger 9000E can be programmed by using the 8950 programmer, the 9075 Smart Programmer, the 9060E
LCD keypad, or the 9001 LED keypad. These methods are described below.
Using a Programmer
Plug the optional 8950 programmer into the 4-pin male outlet marked "programer” on the Ranger 9000E PC Board
and the control will enter the program mode. The 8950 will program locations 000 through 635 of the Ranger
9000E, but requires additional care for locations 400 and above. When the 400 location is reached, the two right 7
segment numeric displays will begin to flash on and off, and the left side numeric display will change to "0". The
flashing is a signal to add a 4 to the left side number to determine which location you are now programming. For
example, if you are in location 575, the left (100's column) will be displaying a "1", the middle (10's column) will be
flashing and displaying a "7", and the right (one's column) will be flashing and displaying a "5". By adding a 4 to the
"1" displayed in left column, it is determined that the location number is 575. See "Using the LED Keypad" below.
(When using the 9075 Smart Programmer, please refer to the 9075 Manual.)
Using The LCD Keypad
The most straightforward method of keypad programming is to utilize the 9060E LCD Keypad in the programming
mode. To access the programming mode enter [C]-[0]-[0], followed by the four digit "Go To Program" access code
which is factory default [9]-[0]-[5]-[0] (this code can be reprogrammed), and follow the keypad prompts. NOTE: If the
9000E is partitioned, all partitions must be disarmed to enter the "Program" mode. (See using the LED Keypad
below.)
Using The LED Keypad
The 9000E can also be programmed by the standard binary method of keypad programming described below.
However, with over 600 locations, this method will be difficult except for the most experienced programmer. When
the 9001 LED keypad is used for programming, enter the factory default four digit "Go To Program" access code of
[9]-[7]-[1]-[3]. NOTE: The Ranger 9000E must be disarmed to gain access to programming with this code. After entry
of this code, the Ranger 9000E will be in the "Program" mode, and the yellow LED's will display the data in location
000. The data is displayed using a Binary system. With this system the yellow zone 1 LED equals "1" when
illuminated. The zone 2 LED equals "2" when illuminated. The zone 3 LED equals "4" when illuminated. The zone
4 LED equals "8" when illuminated. Thus if the data in location 000 is "9", the LED for zone 1 (=1) and zone 4 (=8)
would be illuminated. By adding the two values together, (1+8=9) you would determine that the data in location 000
is "9". If the data in location 000 is "6", the LED or zone 2 (=2) and zone 3 (=4) would be added (2+4=6) indicating
the data in that location to be "6". If no LED's are illuminated, the location contains a "0". To advance from location
000 through 635, press the [#] key. To go to a specific location, press the location number followed by the [#] key.
The yellow LED's will then display the data in that location. Data is changed by entering a number 0 to 15 followed
by [
r
] (
r
= data enter). Review the examples in figure 1 on the following page.
Important Function Codes
There are two function codes that are used in programming the Ranger 9000E and are described below:
[9]-[1]-[0]-[#]
When in the "Program" mode, this function code can be used to write original factory default
codes into the Ranger 9000E, except Locations 636-662.
[9]-[3]-[0]-[#]
This function code is used to exit the programming mode after it was accessed via the keypad.
