Racal Instruments 2460 Series Скачать руководство пользователя | Manualshive

Страница: 15 / 64

background image

User Manual 2460 Series

Installation Instructions 2-2

Racal Instruments



2003

INSTALLATION

The installation of the 2460 Series VXIbus module into a chassis
or mainframe is shown in the following diagram:

Figure 2-1, The installation of the 2460 Series VXIbus Module

Before commencing installation of the 2460 Series VXI Module
instrument, carry out a visual inspection of it. Pay particular
attention to connectors P1 and P2 on the rear of the instrument,
and ensure that there are no bent, damaged or missing pins, any
damage to the instrument should be repaired before proceeding.

Refer to the product identification label on the side of the module
for system integration information relating to voltage, power, and
cooling requirements to be supplied by the VXI chassis.

Switch, S1, is used to set the Logical Address of the module to a
static address or allow the controller to dynamically allocate an
address. The switch is marked for least significant bit (LSB) and
MSB (most significant bit) and logic states 1 and 0.

Static Logical Addresses may be set between the values 1 and
254. If S1 is set to 255, then the controller dynamically allocates
the next available Logical Address. The factory default is 254.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
13
14
15
16
17
...
»

Содержание 2460 Series

































































Отзывы:

Нет отзывов

Похожие инструкции для 2460 Series

Бренд: Eaton Страницы: 6

Бренд: Fairchild Страницы: 2

Бренд: Fairford Страницы: 233

Бренд: Federal Signal Corporation Страницы: 34

Бренд: OMC Страницы: 18

Бренд: Paradox Страницы: 2

Бренд: Paradox Страницы: 2

FrameSaver 9120

Бренд: Paradyne Страницы: 20

VeriSafe VS2-NET

Бренд: Panduit Страницы: 6

Бренд: Yoshitake Страницы: 4

Бренд: YOKOGAWA Страницы: 20

UTAdvanced UT32A

Бренд: YOKOGAWA Страницы: 3

Бренд: Nordelettronica Страницы: 8

Бренд: Olsen Страницы: 4

Бренд: Vent-Axia Страницы: 4

Бренд: Delta Страницы: 16

KaDe KDH-KZ620U

Бренд: AAT Holding Страницы: 28

Бренд: Pulse Shower Spas Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды