Racal Instruments 2460 Series Скачать руководство пользователя

Страница: 14 / 64

User Manual 2460 Series

Racal Instruments



2003

Installation Instructions 2-1

Chapter 2

INSTALLATION INSTRUCTIONS

Unpacking and
Inspection

1. Before unpacking the 2460 Series module, check the

exterior of the shipping carton for any signs of damage. All
irregularities should be noted on the shipping bill.

2. Remove the instrument from its carton, preserving the

factory packaging as much as possible.

3. Inspect the module for any defect or damage. Immediately

notify the carrier if any damage is apparent.

4. Have a qualified person check the instrument for safety

before use.

NOTE:

Proper ESD handling procedures must always be
used when packing, unpacking, or installing any
module. Failure to do so may cause damage to the
unit.

Reshipment
Instructions

1. Use the original packing material when returning module to

Racal Instruments for calibration or servicing. The original
shipping carton and the instrument's plastic foam will
provide the necessary support for safe reshipment.

2. If the original packing material is unavailable, wrap the

switching module in plastic sheeting and use plastic spray
foam to surround and protect the instrument.

3. Reship in either the original or a new shipping carton.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание 2460 Series

































































Результаты поиска

Содержание 2460 Series

Отзывы:

Похожие инструкции для 2460 Series

Бренды по названию

Популярные бренды

Racal Instruments 2460 Series, Руководство пользователя

Результаты поиска

Содержание 2460 Series

Отзывы:

Похожие инструкции для 2460 Series

Бренды по названию

Популярные бренды