Quantech QCC2015CEE Скачать руководство пользователя страница 98

Страница: 98 / 172

QUANTECH

Form QCC2-NM1

Issue Date: 5/20/2021

SECTION 6 – COMMISSIONING

Grounding

Verify that the unit’s protective ground terminal(s) are

correctly connected to a suitable grounding point. En-

sure that all unit internal ground connections are tight.

Supply voltage

Verify that the site voltage supply corresponds to the

unit requirement and is within the limits given in

SEC-

TION 5 – TECHNICAL DATA.

Preparation – Power on

Perform the commissioning using the

detailed checks outlined in the “Equip-

ment Pre-Startup and Startup Check

List” as the commissioning procedure is

carried out.

Apply power to the unit. Turn ON the option panel cir-

cuit breaker if supplied.

The machine is now live!

Switch settings

Ensure that the condensing unit OFF/ON UNIT switch

at the bottom of the keypad is OFF. Place the optional

circuit breaker handle on the panel door to ON. The

customer’s disconnection devices can now be set to

ON.
Verify the control panel display is illuminated. Ensure

the system switches under the SYSTEM SWITCHES

key are in the OFF position.

Compressor heaters

Verify the compressor heaters are energized. If the am-

bient temperature is above 96°F (36°C) the compressor

heaters must be on for at least 8 hours before start-up

to ensure all refrigerant liquid is driven out of the com-

pressor and the oil. If the ambient temperature is below

86°F (30°C), allow 24 hours.

Air flow switch

Verify an air flow switch is correctly fitted in the cus-

tomer’s ductwork and wired into the control panel cor-

rectly using shielded cable.
The air flow switch should be connected to terminals

13 and 14 of XTBC1 on the panel. (See

Figure 10 on

page 37

Содержание QCC2015CEE













































































































































































Результаты поиска

Содержание QCC2015CEE

Отзывы:

Quantech QCC2015CEE, Инструкция по установке, эксплуатации и обслуживанию, Страница: 98 / 172

Результаты поиска

Содержание QCC2015CEE

Отзывы: