Quantech QCC2015CEE Скачать руководство пользователя страница 96

Страница: 96 / 172

QUANTECH

Form QCC2-NM1

Issue Date: 5/20/2021

SECTION 5 – TECHNICAL DATA

Installation of durulene vibration isolators

LD13762B

TOP BOLT

SECTION D-D

TOP WASHER

("A")

("B")

("C")

("B")

1. Read instructions in their entirety before begin-

ning installation.

2. Isolators are shipped fully assembled and are to be

positioned in accordance with the submitial draw-

ings or as otherwise recommended.

Set isolators on floor, housekeeping pad, or sub-

base, ensuring that all isolator centerlines match

the equipment mounting holes. The VMC group

recommends that the isolator base (“A”) be in-

stalled on a level surface. Shim or grout as re-

quired, leveling all isolator bases to the same

elevation (1/32-in. maximum difference can be

tolerated).

4. Bolt or anchor all isolators to supporting structure

utilizing base thru holes (“B”).

5. Remove top bolt and top washer. Place equip-

ment on top of isolators so that mounting holes

in equipment or base line up with threaded hole

(“C”).

6. Reinstall top bolt and washer and tighten down.
7. Installation is complete.

Figure 37 -

Installation of Durulene Vibration Isolators

Содержание QCC2015CEE













































































































































































Результаты поиска

Содержание QCC2015CEE

Отзывы:

Quantech QCC2015CEE, Инструкция по установке, эксплуатации и обслуживанию, Страница: 96 / 172

Результаты поиска

Содержание QCC2015CEE

Отзывы: