manualshive.com logo in svg

Quantech QCC2015CEE, Инструкция по установке, эксплуатации и обслуживанию, Страница: 29 / 172

Поделиться
Скачать
Quantech QCC2015CEE Скачать руководство пользователя страница 29

QUANTECH

29

Form QCC2-NM1 

Issue Date: 5/20/2021

4

To ensure warranty coverage, this equip-

ment must be commissioned and serviced 

by an authorized Quantech service 

mechanic or a qualified service person 

experienced in equipment installation. In-

stallation must comply with all applicable 

codes, particularly in regard to electrical 

wiring and other safety elements such as 

relief valves, HP cutout settings, design 

working pressures, and ventilation re-

quirements consistent with the amount 

and type of refrigerant charge.
Lethal voltages exist within the control 

panels. Before servicing, open and lock-

out/tagout all disconnect switches.

Installation checklist

The following items, 1 through 5, must be checked be-

fore placing the units in operation.

1.  Inspect the unit for shipping damage.
2.  Rig unit using spreader bars. 
3.  Open the unit only to install water piping sys-

tem. Do not remove protective covers from water 

connections until piping is ready for attachment. 

Check water piping to ensure cleanliness.

4.  Pipe unit using good piping practice

 (see ASHRAE 

handbook section 215 and 195).

5.  Check to see that the unit is installed and operated 

within limitations

 (Refer to Limitations).

The following pages outline detailed procedures to be 

followed to install and start-up the unit.

Handling

These units are shipped as completely assembled units 

containing full operating charge, and care should be 

taken to avoid damage due to rough handling. 

Location and clearances

These units are designed for outdoor installations on 

ground level, rooftop, or beside a building. Location 

should be selected for minimum sun exposure and to 

ensure adequate supply of fresh air for the condenser. 

The units must be installed with sufficient clearances 

for air entrance to the condenser coil, for air discharge 

away from the condenser, and for servicing access.

Section 4 – Installation

In installations where winter operation is intended and 

snow accumulations are expected, additional height 

must be provided to ensure normal condenser air flow.
Clearances are listed in 

DIMENSIONS (ENGLISH)

.

Foundation

The unit should be mounted on a flat and level foun-

dation, floor, or rooftop capable of supporting the en-

tire operating weight of the equipment. 

See Table 6 on 

page 40 

for operating weight

. 

If the unit is elevated 

beyond the normal reach of service personnel, a suit-

able catwalk must be capable of supporting service 

personnel, their equipment, and the compressors.

Ground level locations

It is important that the units be installed on a sub-

stantial base that will not settle. A one piece concrete 

slab with footers extended below the frost line is 

highly recommended. Additionally, the slab should 

not be tied to the main building foundations as noise 

and vibration may be transmitted. Mounting holes are 

provided in the steel channel for bolting the unit to its 

foundation. See

 DIMENSIONS (ENGLISH).

For ground level installations, precautions should be 

taken to protect the unit from tampering by or injury to 

unauthorized persons. Screws and/or latches on access 

panels will prevent casual tampering. However, further 

safety precautions such as a fenced-in enclosure or 

locking devices on the panels may be advisable.

Rooftop locations

Choose a spot with adequate structural strength to 

safely support the entire weight of the unit and service 

personnel. Care must be taken not to damage the roof.
Consult the building contractor or architect if the roof is 

bonded. Roof installations should have wooden beams 

(treated to reduce deterioration), cork, rubber, or vibra-

tion isolators under the base to minimize vibration.

Noise sensitive locations

Efforts should be made to ensure that the unit is not 

located next to occupied spaces or noise sensitive areas 

where unit noise level would be a problem. Unit noise 

is a result of compressor and fan operation. Consider-

ations should be made using noise levels published in 

the Quantech Engineering Guide for the specific con-

densing unit model. Sound blankets for the compres-

sors and low sound fans are available. 

Содержание QCC2015CEE













































































































































































Отзывы:

Нет отзывов