Quantech QCC2015CEE Скачать руководство пользователя страница 111

Страница: 111 / 172

QUANTECH

111

SECTION 7 – UNIT CONTROLS

Form QCC2-NM1

Issue Date: 5/20/2021

Display/Print keys

00067VIP

The DISPLAY/PRINT keys allow the user to retrieve

system and unit information that is useful for moni-

toring unit operation, diagnosing potential problems,

troubleshooting, and commissioning the unit.
System and unit information, unit options, setpoints,

and scheduling can also be printed out with the use of

a printer. Both real-time and history information are

available.

Oper Data key

The OPER DATA key gives the user access to unit and

system operating parameters. When the OPER DATA

key is pressed, system parameters will be displayed

and remain on the display until another key is pressed.

After pressing the OPER DATA key, the various op-

erating data screens can be scrolled through by using

the ↑ (UP) and ↓ (DOWN) arrow keys or the ENTER/

ADV key located under the “ENTRY” section.

System 2 information will only be dis-

played for 2 system units.

With the “UNIT TYPE” set as a condensing unit (via

jumper between J11-7 and J11-12 on the I/O Board),

the following list of operating data screens are view-

able under the OPER DATA key in the order that

they are displayed. The

↓

(DOWN) arrow key scrolls

through the displays in the order they appear below:

The unit MUST be set to be a condensing

unit via jumper between J11-7 and J11-12

on the I/O Board. DO NOT operate the

unit if not correctly set up.

D I S C H A R G E A I R T E M P
= 5 7 . 4 ° F

This display shows the discharge air temperature leav-

ing the evaporator. The display will only be shown

when the Control Mode is programmed for Discharge

Air (under the OPTIONS key). The minimum limit on

the display for these parameters are 9.2°F (-12.7°C).

The maximum limit on the display is 85.4°F (29.7°C).

A M B I E N T A I R T E M P

= 8 7 . 5 ° F

This display shows the ambient air temperature. The

minimum limit on the display is 0.4°F (-17.6°C). The

maximum limit on the display is 131.2°F (55.1°C).

Содержание QCC2015CEE













































































































































































Результаты поиска

Содержание QCC2015CEE

Отзывы:

Quantech QCC2015CEE, Инструкция по установке, эксплуатации и обслуживанию, Страница: 111 / 172

Результаты поиска

Содержание QCC2015CEE

Отзывы: