manualshive.com logo in svg

Quantech QCC2015CEE, Инструкция по установке, эксплуатации и обслуживанию, Страница: 101 / 172

Поделиться
Скачать
Quantech QCC2015CEE Скачать руководство пользователя страница 101

QUANTECH

101

SECTION 6 – COMMISSIONING

Form QCC2-NM1 

Issue Date: 5/20/2021

6

FORM 150.63-CL2 

ISSUE DATE: 10/31/2013

P.O. Box 1592, York, Pennsylvania USA 17405-1592 

800-861-1001 

Subject to change without notice. Printed in USA

Copyright © by Johnson Controls 2013 

www.johnsoncontrols.com 

ALL RIGHTS RESERVED

Form 150.63-CL2 (1013)
Issue Date: October 31, 2013 
NEW RELEASE

D. CHECKING SUPERHEAT AND SUBCOOLING

The subcooling temperature of each system can 
be calculated by recording the temperature of the 
liquid line at the outlet of the condenser and sub-
tracting it from the liquid line saturation tempera-
ture at the liquid stop valve (liquid line saturation 
temp. is converted from a temperature/pressure chart).

Example:
 Liquid line pressure =
 202 PSIG converted to temp.   102°F
  minus liquid line temp.  - 84°F
  

Subcooling =   18°F

The subcooling should be adjusted to 18°F at design condi-

tions.

1.  Record the liquid line pressure and its corre-

sponding temperature, liquid line temperature and 
subcooling below: ....................................................

  

  SYS 1    SYS 2

 

Liq Line Press =  _______  _______ PSIG

 

Saturated Temp =  _______  _______ °F

 

Liq Line Temp =  _______  _______ °F

 

Subcooling =  _______  _______ °F

After  the  subcooling  is  verified,  the  suction  superheat 

should be checked. The superheat should be checked 
only after steady state operation of the condensing 
unit has been established, the leaving water tempera-
ture has been pulled down to the required leaving wa-
ter temperature, and the unit is running in a fully loaded 
condition. Correct superheat setting for a system is 10°F 
to 15°F (5.56°C to 8.33°C) 18” (46 cm) from the cooler.

Superheat should typically be set for no less than 

10°F with only a single compressor running on a 

circuit.

 The superheat is calculated as the difference 

between the actual temperature of the returned refrig-
erant gas in the suction line entering the compressor 
and the temperature corresponding to the suction pres-
sure as shown in a standard pressure/temperature chart.

Example:

 

Suction Temp =  46°F

 

minus Suction Press

  60 PSIG converted to Temp   - 34°F

 

Superheat =   12°F 

When adjusting the expansion valve (TXV only), the 
adjusting screw should be turned not more than one 

turn at a time, allowing sufficient time (approximately 

15 minutes) between adjustments for the system and 
the thermal expansion valve to respond and stabilize.
Assure that superheat is set at a minimum of 10°F 
(5.56°C) with a single compressor running on each circuit.
2.  Record the suction temperature, suction pressure, 

suction saturation temperature, and superheat of 
each system below:  ................................................

  

 SYS 1   SYS 2

 

Suction Temp =  _______  _______ °F

 

Suction Pressure =  _______  _______ PSIG

 

  Saturation Temp =  _______  _______ °F

 

Superheat =  _______  _______ °F

E. LEAK CHECKING

Leak  check  compressors,  fittings,  and  piping  to  en

-

sure no leaks.  ..............................................................
If the unit is functioning satisfactorily during the ini-
tial operating period, no safeties trip and the com-
pressors cycle to control water temperature to 
setpoint, the chiller is ready to be placed into operation.

Owner's operating personnel:

Name: 

___________________________________________________

Phone Number: 

__________________________________________

Name: 

___________________________________________________

Phone Number: 

__________________________________________

Name: 

___________________________________________________

Phone Number: 

__________________________________________

Содержание QCC2015CEE













































































































































































Отзывы:

Нет отзывов