Quantech QCC2015CEE Скачать руководство пользователя страница 95

Страница: 95 / 172

QUANTECH

SECTION 5 – TECHNICAL DATA

Form QCC2-NM1

Issue Date: 5/20/2021

Durulene isolator cross-reference

MOUNT

TYPE

DIMENSION DATA (INCHES)

RD1-WR

3.13

1.75

1.25

2.38

0.34

0.19

5/16-18 UNC X 3/4

1.25

RD2-WR

3.88

2.38

1.75

3.00

0.34

0.22

3/8-16 UNC X 1

1.75

RD3-WR

5.50

3.38

2.88

4.13

0.56

0.25

1/2-13 UNC X 1

2.50

RD4-WR

6.25

4.63

2.75

5.00

0.56

0.38

1/2-13 UNC X 1

3.00

MODEL NUMBER

RATED

CAPACITY

[LB]

RATED

DEFLECTION

[IN.]

DURO

(± 5)

RD2-Light Blue-WR

0.4

RD2-Brown-WR

0.4

RD2-Brick Red-WR

0.4

RD 2-Lime-WR

120

0.4

MODEL NUMBER

RATED

CAPACITY

[LB]

RATED

DEFLECTION

[IN.]

DURO

(± 5)

RD2-Light Blue-WR

135

0.5

RD2-Brown-WR

170

0.5

RD2-Brick Red-WR

240

0.5

RD 2-Lime-WR

380

0.5

RD2 Charcoal-WR

550

0.5

MODEL NUMBER

RATED

CAPACITY

[LB]

RATED

DEFLECTION

[IN.]

DURO

(± 5)

RD3-Brown-WR

250

0.5

RD3-Brick Red-WR

525

0.5

RD3-Lime-WR

750

0.5

RD3-Charcoal-WR

1100

0.5

MODEL NUMBER

RATED

CAPACITY

[LB]

RATED

DEFLECTION

[IN.]

DURO

(± 5)

RD4-Brown-WR

1500

0.5

RD4-Brick Red-WR

2250

0.5

RD4-Lime-WR

3000

0.5

RD4-Charcoal-WR

4000

0.5

Figure 36 -

Durulene Isolator Cross-Reference

NOTES:

1. All dimensions are inches, interpreted per ANSI Y14.

Refer to next page for installation instructions.

3. Mount molded in weather resistant duralene compound as stan-

dard. Also available in other materials such as natural rubber,

extreme high temperature silicone, high-damped silicone, nitrile

and EDPM.

4. AL = Mounting hole center to center spacing.

5. HF = Free height of mount, before loading. Operating height

calculated by the free height less the static deflection under

load. All dimensions for reference only.

6. Hardware is zinc-electroplated.

Содержание QCC2015CEE













































































































































































Результаты поиска

Содержание QCC2015CEE

Отзывы:

Quantech QCC2015CEE, Инструкция по установке, эксплуатации и обслуживанию, Страница: 95 / 172

Результаты поиска

Содержание QCC2015CEE

Отзывы: