Quantech QCC2015CEE Скачать руководство пользователя страница 109

Страница: 109 / 172

QUANTECH

109

SECTION 7 – UNIT CONTROLS

Form QCC2-NM1

Issue Date: 5/20/2021

Unit warning

The following messages are not unit safeties and will

not be logged to the history buffer. They are

unit warn-

ings

and will not auto-restart. Operator intervention is

required to allow a restart of the unit.

! ! L O W B A T T E R Y ! !

C H E C K P R O G / S E T P / O P T N

The Low Battery Warning can only occur at unit pow-

er-up. On micro panel power-up, the RTC battery is

checked. If a low battery is found, all programmed

setpoints, program values, options, time, schedule, and

history buffers will be lost. These values will all be re-

set to their default values which may not be the desired

operating values. Once a faulty battery is detected, the

unit will be prevented from running until the PRO-

GRAM key is pressed. Once PROGRAM is pressed

the anti-recycle timers will be set to the programmed

anti-recycle time to allow the operator time to check

setpoints, and if necessary, reprogram programmable

values and options.

If a low battery is detected, it should be replaced as

soon as possible. The programmed values will all be

lost and the unit will be prevented from running on the

next power interruption. The RTC/battery (031-02565-

000) is located at U5 on the IPU microboard (031-

02630-000).

I N C O R R E C T

U N I T T Y P E

This indicates the condensing unit jumper is not in-

stalled between J11-7 and J11-12, on the I/O Board.

This jumper must be installed to operate the condens-

ing unit.

Содержание QCC2015CEE













































































































































































Результаты поиска

Содержание QCC2015CEE

Отзывы:

Quantech QCC2015CEE, Инструкция по установке, эксплуатации и обслуживанию, Страница: 109 / 172

Результаты поиска

Содержание QCC2015CEE

Отзывы: