manualshive.com logo in svg

Quantech QCC2015CEE, Инструкция по установке, эксплуатации и обслуживанию, Страница: 100 / 172

Поделиться
Скачать
Quantech QCC2015CEE Скачать руководство пользователя страница 100

QUANTECH

100

Form QCC2-NM1 

Issue Date: 5/20/2021

SECTION 6 – COMMISSIONING

JOHNSON CONTROLS

2

FORM 150.63-CL2 

ISSUE DATE: 10/31/2013

Setpoints Entry List

OPTIONS

Display Language
SYS 1 Switch
Sys 2 Switch
Chilled Liquid

* Ambient Control

Local/Remote Mode
Control Mode
Display Units

* Lead/Lag Control
* Fan Control

Manual Override
Current Feedback

** Soft Start
** Unit Type
** Refrigerant Type
** Expansion Valve Type

COOLING SETPOINTS

Cooling Setpoint
Range
EMS-PWM Max. Setpoint

PROGRAM

Discharge Pressure Cutout
Suct. Pressure Cutout
Low Amb. Temp. Cutout
Anti-Recycle Time
Fan Control On Pressure
Fan Differential Off Pressure
Total # of Compressors

* Number of Fans/System
* Unit/Sys Voltage

Unit ID

* Sys 1 Superheat Setpoint
* Sys 2 Superheat Setpoint

* Not on All Models 

** Viewable  Only

Place the Unit Switch in the control panel to the 
“ON” position. As each compressor cycles ON, en-
sure that the discharge pressure rises and the suc-
tion pressure decreases. If this does not occur, the 
compressor being tested is operating in the reverse 
direction and must be corrected. After verifying prop-
er compressor rotation, turn the Unit Switch to “OFF.”

The discharge air or suction pressure 

setpoint may need to be temporarily 

lowered to ensure all compressors cycle 

“ON.”

This unit uses scroll compressors which 

can only operate in one direction. Failure 

to observe this will lead to compressor 

failure.

6.  Turn system 1 “off” and system 2 “on” (refer to Op-

tion 2 under “UNIT keys” in Section 7 for more in-
formation on system switches).  ...............................

Place the Unit Switch in the control panel to the 
“ON” position. As each compressor cycles “on”, en-
sure that the discharge pressure rises and the suc-
tion pressure decreases. If this does not occur, the 
compressor being tested is operating in the reverse 
direction and must be corrected. After verifying prop-
er compressor rotation, turn the Unit Switch to “OFF”.

The chilled liquid setpoint may need to 

be temporarily lowered to ensure all com-

pressors cycle “ON”.

Содержание QCC2015CEE













































































































































































Отзывы:

Нет отзывов