Predator Gas SE Скачать руководство пользователя страница 26

Страница: 26 / 38

Step 59 Upper Rotorhead Pushrods

Attach pushrod A to the washout control arms and

pushrod C from the single side of the bell mixer down

the to the long ball on the inner race of the swashplate,

being careful when connecting ball links to install the

link in the correct direction. When the collective stick is

centered the blade pitch should be set to 0

degrees and

the bell mixer, flybar arms, washout arms and swashplate

should be parallel. It should be noted that a perfect paral-

lel geometry is not possible but get as close as to parallel

as possible within one half ball link rotation.

Pushrod G 56.5mm

(center to center) x 2

#HI6145 Ball Link Set

(26 long & 4 short)

Pushrod A 47mm (cen-

ter to center) x 2

Pushrod C 99mm (cen-

ter to center) x 2

#HI6192 Upper Linkage

Rod Set (6 rods)

Parallel

Pushrod B 26mm (cen-

ter to center) x 2

#HW6001 M5x35

Socket Cap Screws x 2

& M5 Locknut x 2

Main blade grips shown

at 0

degrees.

When attaching all pushrods,

make sure that same length

pushrods are actually the same

length from the beginning oth-

erwise it will be difficult later

to figure out where the source

of the linkage problems.

Mode Description

Low Mid High

Normal

-6

+10

Idle Up 1

-10

+10

Idle Up 2

-10

+10

Throttle Hold

-10

+12

The following table should be used as a guide while

setting up the pitch curves in the different flight

modes on the transmitter.

Pitch Range Settings

Step 58A Radio Switch Mount

#CN2290

Switch Mount

M2.3x12 Self

Tap Screws x 4 &

#HI3205 Servo

Mount Tabs x 2

Position the switch mount plate in the empty servo

opening. Install the switch and insert two M2.3x12

Phillips self tapping screws through the left side and

start the servo mount tabs. Slide the plate in place and

secure the right side screws. Normally, the switch is

off in the rear position.

Содержание Gas SE







































Результаты поиска

Содержание Gas SE

Отзывы:

Predator Gas SE, Инструкция по эксплуатации, Страница: 26 / 38

Результаты поиска

Содержание Gas SE

Отзывы: