Predator Gas SE страница 11 Скачать руководство пользователя

Страница: 11 / 38

Step 20 Rear & X Frame Assembly

Align the rear X frame with the left side of the rear

lower frame (notice the spark plug access holes

align) for the spark plug wire. Insert one M3x8

socket cap screw from the outside of the lower

frame, through the lower hole only in the X frame

and secure with an M3 locknut on the inside. At-

tach the right side lower frame in exactly the same

way.

Assemble these bolts only to position the frames

at this time, they will be tightened when the up-

per frames are installed. Note that the upper hole

remains empty until that time also.

#HW6117A

Rear X Frame

#HW6115C

Rear Lower

Frames - Left

Side

M3x8 Socket

Cap Screw &

M3 Locknut x 2

Align the

cutouts.

Step 21 Rear Lower &Bottom Frame

Slide the rear frame assembly over the land-

ing gear frame and insert the spark plug wire

through the cutout in the left side frame and

the X frame. Insert four M3x8 socket cap

screws through the lower frames into the

landing gear frame, do not use threadlock at

this time. Press the spark plug cap over the

spark plug in the engine. Similarly, the M3x8

socket cap screws will not be tightened until

after the upper frames are installed.

Attached to the coil is a black wire, this is

generally not used in helicopters and should

be secured out of the way with a cable tie.

#HW6117B

Landing Gear

Frame

Spark Plug Wire

with isolator,

through the

frames.

M3x8 Socket

Cap Screw x 4

Black coil

engine lead,

not used.

Step 22 Battery Tray

Four M3x20 socket cap screws need to

be installed from the inside and threaded

through the battery tray. After the fuel tank

is installed, there is no access to hold the

head of these bolts. We recommend that

these bolts be bonded in placing using

L262 Red threadlock (JB Weld or Slow

Cyanoacrylate glue can be used as an

alternative) to permanently bond these

bolts in place.

M3x20 Socket

Cap Screw x 4

#HW6112C

Battery Tray

Содержание Gas SE







































Результаты поиска

Содержание Gas SE

Отзывы:

Похожие инструкции для Gas SE

Бренды по названию

Популярные бренды

Predator Gas SE, Инструкция по эксплуатации

Результаты поиска

Содержание Gas SE

Отзывы:

Похожие инструкции для Gas SE

Бренды по названию

Популярные бренды