manualshive.com logo in svg

Predator Gas SE, Инструкция по эксплуатации, Страница: 31 / 38

Поделиться
Скачать
Predator Gas SE Скачать руководство пользователя страница 31

31

Step 72  Carbon Tail Rotor Blades - Gas SE

The carbon tail rotor blades will not fit the tail rotor 

grips without trimming the ends. Attach the two 

rotor blades together and grind 3-4mm off the end 

of both blades as shown.

#HI6099A 95mm 

Tail Rotor Blades x 2

#HW6001 M3x18 

Special Socket Cap 

Screw

#HW6204 

M3x10x1.5 

Spacers x 4

CN261056 

105mm Rotortech 

Tail Blades x 2 

Gas SE only

Grind 3-4mm 

off the end of the 

blades.

Step 73  Mount Tail Blades

Slide one M3x18 special socket cap screw from the inside of the tail rotor 

grip and position the first M3x10x1.5 spacer, insert the tail blade, another 

spacer and secure using one M3 locknut from the molded recess on the out-

side.When correctly installed, the leading edge of the tail rotor blades will 

rotate into the down wash from the main rotor blades.

M3 

Locknut

#HW6001 M3x18 

Special Socket Cap 

Screw

#HW6204 

M3x10x1.5 

Spacer x 2

Tail blade tension should be set tight enough that the rotor blade 

will stay straight on its own, but will pivot easily when the blade 

tip is moved.

After flying the model, if a vibration is noticed on the horizontal 

fin, the complete tail rotor assembly can be removed with the hub 

and further balanced using a High Point balancer.

Step 74  Tail Boom Transmission Mount

Insert four M3x12 socket cap screws through 

the tail transmission mount over the tail boom 

(make sure the tail rotor is on the right side 

when viewed from behind) and secure with 

four M3 locknuts inserted into the molded 

recesses. Look at the threaded hex spacers and 

make sure that they are flush on both sides of 

the mount. Slide the completed tail boom as-

sembly, aligning the three holes on the upper 

side frames and roughly position the tail bevel 

gear on the inner gear. Insert two M3x10 flat 

head cap screws and four M3x8 socket caps 

screws using L242 Blue threadlock. Do not 

overtighten these bolts!

M3x12 Socket Cap 

Screw x 4 & M3 

Locknut x 4

M3x8 Socket Cap 

Screw x 2

M3x10 Flat Head 

Screw x 2

Содержание Gas SE







































Отзывы:

Нет отзывов