manualshive.com logo in svg

Predator Gas SE, Инструкция по эксплуатации, Страница: 7 / 38

Поделиться
Скачать
Predator Gas SE Скачать руководство пользователя страница 7

7

Step 9 Flybar & Flybar Paddles 

Slide and center the flybar through the head assembly. Carefully look at the flybar control arm assemblies from the previous 

step and notice that when installed correctly, the securing set screw is on top. Insert one M4x6x0.5 micro washer #CNLR1006 

against each bearing then slide the control arm halves onto each side, so that they match together and the set screw remains on 

top. Insert one M3x12 button head socket screw to secure the opposite standoff, hold the tapered standoff using pliers while 

tightening the screw (to avoid the double studded ball from stripping the plastic threads in the center). Loosely tighten the 

M4x5 set screws into the round aluminum inserts aligned with the flat spots on the flybar. Using a ruler, check the distance 

between the end of the flybar and the control arm and adjust until the lengths are the same. Tighten both set screws, one at 

a time using L242 Blue threadlock. Make a pencil mark 5mm past the threads on both ends of the flybar. Thread the flybar 

paddles onto the flybar until the mark is reached, align the paddles parallel. Again using the ruler, rotate one paddle or the 

other to get equal distances, remember leading edge of the paddles turn clockwise.

Set the length of pushrod B to 26mm (center to center) and attach to the ball on the adjustable side of the bell mixer and to 

the steel ball on the lower seesaw assembly. Check the ball links for proper fit, adjusting if necessary and remember that the 

bell mixer is positioned on the leading edge as the rotor head rotates clockwise.

Pushrod B

26mm (center to center)

#HI6145 Short Ball Link x 2 

#HW6192 14mm Pushrod x 2

Note: Bell Mixer 

positioned on 

leading edge 

as head rotates 

clockwise.

#HW6173 Flybar 520mm

*packed with tailboom.

M4x5 Set 

Screw

M3x12 Button 

Head Screw

HI6179B  30gr Sport  Black  Gas

#HI6009A Cooling Fan

M3x6 Flat Head 

Screws x 4

Step 10 Cooling Fan

The  cooling  fan  hub  and  fan  comes  assembled  but 

requires final assembly. Remove each of the M3x6 flat 

head screws one at a time, apply L242 Blue threadlock 

and tighten back into the cooling fan hub.

If a governor is planned to be installed, install magnets 

into the holes provided in the bottom of the cooling 

fan. A similar hole has been made in the cooling fan 

shroud mount plate to mount the sensor on the right 

side (muffler side) of the engine. 

#HW6012HDV2 

Cooling Fan 

Hub

Holes for installing 

governor magnets.

Содержание Gas SE







































Отзывы:

Нет отзывов