Predator Gas SE страница 14 Скачать руководство пользователя

Страница: 14 / 38

Step 29 Clutch Bell & Short Bearing Block

Apply a small amount of L262 Red threadlock to the top edge of the

clutchbell and press in place using a thin walled automotive socket that puts

pressure only on the inside race of the ball bearing. Pressing from the outside race will damage the bearing which is not

covered by warranty. Finally, re-install the pinion being careful not to cross the threads using L242 Blue threadlock.

#HW6013HD

Clutch Bell As-

sembly 15T

Pre-Assembled

As the 15T pinion has a larger diameter than the top sur-

face of the clutchbell, it must be removed before the clutch

bearing is changed or installed. The pinion has a standard

right hand thread, if available use strap-wrenches, grip the

outside of the pinion and the clutch bell firmly and turn

anti-clockwise. The bearing must be installed into the

bearing block before it is installed onto the clutchbell.

Clean the inside race of the ball bearing and the surface

that where the clutchbell will be installed.

Step 30 Clutch Shaft & Lower Long

Bearing Block

Clean the top of the pinion gear and the inside surfaces of both the

upper and lower bearings inside the clutch shaft bearing block us-

ing alcohol. Apply a small amount of L262 Red threadlock to the

top edge of the clutch gear where it will contact the bearing. Press

the bearing block in place, firmly seating the bearing against the

top of the pinion gear. Insert two M3x12 socket cap screws from

below to attach the long bearing block to the short block. Do not

use threadlock until the gear mesh has been set.

#HW6045HD Lower

Long Bearing Block

(flange down)

M3x12 Socket

Cap Screws x 2

#HW6007

Clutch Shaft

Bearing Block

Step 31 Upper Canopy Mount

Looking carefully at the upper frames, the longer canopy mount is in-

stalled on the same side as the counter sunk hole above the main gear.

Install one M3x8 button head screw from the inside of the frame using

L242 Blue threadlock. Repeat for both upper frames.

M3x10 Button

Head Screw

#HW6125A

Long Up-

per Canopy

Mount

#HW6110A

Upper Side

Frame

(Right)

Gas SE only

Step 32

Upper Main Shaft Bear-

ing Block - Gas SE

M3x8 Socket

Cap Screw x 2

Install the upper main shaft bearing block into the upper

holes in the left side of the upper frame using two M3x8

socket cap screws. Do not use threadlock at this time,

until after the main shaft is installed.

#HW6042A

Triple Bearing

Block

#HW6045HD

Lower Short Bear-

ing Block

Содержание Gas SE







































Результаты поиска

Содержание Gas SE

Отзывы:

Похожие инструкции для Gas SE

Бренды по названию

Популярные бренды

Predator Gas SE, Инструкция по эксплуатации

Результаты поиска

Содержание Gas SE

Отзывы:

Похожие инструкции для Gas SE

Бренды по названию

Популярные бренды