Predator Gas SE страница 22 Скачать руководство пользователя

Страница: 22 / 38

Step 51 Swashplate

Starting with the inside race, apply L242

Blue threadlock to the two long silver steel

balls and attach them across from each

other. The balls need to be started by hand

at one of the holes in the outer swashplate

rim and then tightened with an M2.0 hex

key through the same hole. Insert two short

steel balls across from each other using

L242 Blue threadlock. Intall three short steel

balls on the outside ring in either the 120

degree (normal) or 140

degree positions

using threadlock.

#HW6146B

120 Degree

Swashplate

Assembly

#CNLR1014

Short Steel

Ball x 5

#CNLR1019 Long

Steel Ball x 2

Step 52 Washout Assembly

Apply a small amount of slow cyanoacry-

late (Slo CA) glue Attach the two medium

steel balls to the end of the washout control

arms, do not overtighten the balls into the

plastic. Press one M3x7 ball bearing into

one side followed by one M3x5x3 spacer

and the second ball bearing from the other

side. Insert one M3x15 button head screw

from the hollowed side of the washout

arm, slide one M3x5x0.5 micro washer

and apply a small amount of Slo CA glue

to the exposed threads and thread into the

washout hub, again being carefull not to

overtighten the screw. When correctly as-

sembled the screw is positioned on the left

side (see photo) of the main shaft.

#HI3152C

Washout As-

sembly

#HI3152A

Radius Link

& Pin

#CNLR1020

Medium

Steel Ball x 2

#HW6001 M3x16 But-

ton Head Screw x 2

#CNBB37 M3x7

Ball Bearing x 4

#HI6205

M3x5x3 Steel

Spacer x 2

#CNLR1003

M3x5x0.5 Micro

Washer x 2

Step 53 Rotorhead Attachment

Slide the swashplate followed by the washout

unit (make sure the screw is on the left side of

the main shaft), the washout guide and the ro-

tor head onto the main shaft. Insert the M4x22

shoulder socket cap screw through the rotor

head hub and main shaft and secure with one

M4 locknut, torque down the screw. Apply

L242 Blue threadlock to the M2.5x8 socket

cap screws and tighten into the bottom of the

rotor head block to clamp against the main

shaft, do not overtorque. Position the washout

guide against the collar and align one hole to

the vertical slot in the rotor head. Apply L242

Blue threadlock to the M3x4 set screws and

evenly tighten set screws in place.

#HW6001 M4x22

Shoulder Socket

Cap Screw & M4

Locknut

M2.5x8 Socket

Cap Screw x 2

#HI6153 Washout

Guide & M3x4 Set

Screw x 2

#HW6053

Main Shaft

Содержание Gas SE







































Результаты поиска

Содержание Gas SE

Отзывы:

Похожие инструкции для Gas SE

Бренды по названию

Популярные бренды

Predator Gas SE, Инструкция по эксплуатации

Результаты поиска

Содержание Gas SE

Отзывы:

Похожие инструкции для Gas SE

Бренды по названию

Популярные бренды