Predator Gas SE страница 18 Скачать руководство пользователя

Страница: 18 / 38

Step 40 Main Gear Pin

Before the main gear assembly can be installed this spacer must be positioned

in the recess of the lower bearing block assembly, it will simply self align in the

block. Slide the main shaft through the upper bearing block, the constant drive main gear assembly, the spacer and finally

through the lower bearing block assembly. Look carefully through the two open M4 threaded holes in the top hub and align

with the hole in the main shaft. Insert and press the M3x15 steel pin through the hub and roughly center it in the main shaft.

Using a permanent marker, mark both holes that will lock the pin in place. Insert the M4x4 set screws in each side and tighten

them equally, using L242 Blue threadlock. These do not need to be torqued down.

#HW6001 M3x15 Steel Pin

& M4x4 Set Screws x 2

Do not remove

the two set screws

that are already

installed in the top

auto hub, these are

factory installed.

Step 41 Bottom Collar

Inspect the bottom collar, make sure that the reduced step

diameter is towards the ball bearing. Slide the bottom

collar against the bearing and insert two M3x6 flat head

cap screws using L242 Blue threadlock.

#HW6054 Bottom Collar &

M3x6 Flat Head Screws x 2

Step 42 Bottom Collar - Gas SE

Slide the flat side of the thrust bearing spacer against the bear

ing, followed by the larger ID race, apply grease to the ball race

and and finally the smaller ID race

. Slide the bottom collar with

the flat side towards the thrust bearing and insert two M3x6 flat

head cap screws using L242 Blue threadlock.

#HW6054 Bottom Collar &

M3x6 Flat Head Screws x 2

#HW6045B Thrust

Bearing Spacer

Offset step

away from

thrust bearing.

Gas SE only

Now that the main shaft is installed, remove the

four screws that secure the upper main shaft bear-

ing block and the forwardmost lower bearing block

screw and one at a time and apply L242 Blue

threadlock and tighten in place.

#HW6054

M10x14x3.5 Spacer

Mark the set screws that

secure the pin.

Step 39 Auto Hub Spacer

thick race

(lower)

smaller ID

thin

race

(upper)

larger ID

#CNBB1018T

Main Shaft

Thrust Bearing

Содержание Gas SE







































Результаты поиска

Содержание Gas SE

Отзывы:

Похожие инструкции для Gas SE

Бренды по названию

Популярные бренды

Predator Gas SE, Инструкция по эксплуатации

Результаты поиска

Содержание Gas SE

Отзывы:

Похожие инструкции для Gas SE

Бренды по названию

Популярные бренды