Predator Gas SE страница 27 Скачать руководство пользователя

Страница: 27 / 38

Step 60 Landing Gear Assembly

Assemble the metal landing skids

onto the plastic struts, noting that the

correct direction is to have the struts

sweep forward. Position the rear strut

at 37mm from the end of the skid and

secure the M3x5 set screw. Leave the

front strut loose for now.

#HI6122 Landing Gear

Plastic Struts x 2

#HW6123 Landing

Gear Metal Skids x 2

~ 1 1/2”

[37mm]

M3x5 Set Screws x 4

Step 61 Landing Gear Spacers

Measure and drill new holes spaced 60mm

apart for the landing struts. Starting with

the rear landing strut, insert two M3x35

socket cap screws with M3x11 flat washers

from the bottom of the plastic strut, through

the landing gear spacers. Apply L242 Blue

threadlock to the exposed threads and thread

into the landing gear frame. Align the front

struts and attach the bolts and spacers. Re-

member to insert and secure the remaining

two M3x5 set screws to secure the front

landing struts to the skids.

#HW6127C

M3x15x19 Landing

Gear Spacers x 4

M3x35 Socket Cap Screws x 4

& M3x11 Flat Washers x 4

#CNBB511 M5x11

Ball Bearing x 2

#HW3057

Tail Bevel

Gear

#HW6059 Tail

Transmission Out-

put Shaft

M3x5 Set

Screw

#HW6059 M5x10 Col-

lar, M5x7x2 Spacers x 2

& M3x5 Set Screw

#HI6154 Torque

Tube Drive Coupler

& M4x5 Set Screw

#HI6060A Front

Tail Transmission

Step 62 Tail Transmission

The tail transmission output shaft is

already assembled. We suggest that

you disassemble the components and

carefully bond the bearings in place

using L262 Red threadlock. Starting

with the M5x10 collar positioned on

the middle flat spot on the shaft. Slide

one M5x7x2 spacer and M5x11 ball

bearing on the short end and carefully

bond the bearing. Slide another spacer

and finally the torque tube fitting and

its M4x5 set screw using L242 Blue

threadlock. Slide the gear and position

and bond the front bearing using the

transmission for alignment.

Insert the M3x5 set screw into the bevel

gear but leave this loose until after the

transmission has been installed and the

tail gear mesh is set.

Содержание Gas SE







































Результаты поиска

Содержание Gas SE

Отзывы:

Похожие инструкции для Gas SE

Бренды по названию

Популярные бренды

Predator Gas SE, Инструкция по эксплуатации

Результаты поиска

Содержание Gas SE

Отзывы:

Похожие инструкции для Gas SE

Бренды по названию

Популярные бренды