Predator Gas SE Скачать руководство пользователя страница 24

Страница: 24 / 38

Before the carburetor arm is tightened to the to the carburetor throttle shaft, the pushrod will be attached and adjusted to

achieve a linear geometry that will result in a 90

degree angle between the pushrod and both the servo horn and the machined

carburetor arm. Install one steel ball into the carburetor arm positioned in the center hole (13.5mm from the center of the arm)

and the servo horn at 13.5mm, using L242 Blue threadlock. If you have not already done so, shorten the throttle pushrod from

104mm to 94mm by cutting 5mm off each end. Install the ball links and set pushrod F to 112mm center to center. Move the

collective stick to the center and press the servo horn onto the servo close to the final angle. Slide the carburetor arm over

the throttle lever shaft and attach Pushrod F. Using the subtrim on the throttle channel, fine tune the servo horn to achieve the

degree setting. Looking through the venturi, move the valve to the 45

position and lightly tighten the M3x4 set screw

on the side of the carburetor arm. Check the end points and continue to adjust the set screw postion until the carburetor will

move through the entire throttle range with out binding. Once complete, firmly hold the external throttle lever, remove and

apply L242 Blue threadlock to the M3x4 set screw and tighten in place.

Step 57 Throttle Pushrod & Carburetor Arm

#HW6192C

Pushrod F 112mm

(center to center)

#HW6192B Car-

buretor Arm &

M3x4 Set Screw

Optional

#CN2288 Metal

Servo Arm Pack

Degrees

#CNLR1018 Ultra

Short Steel Ball &

M2 Hex Nut

#CNLR1018 Ultra

Short Steel Ball &

M2 Hex Nut

Step 56 Idle Adjustment Screw & Carburetor Spring

The idle adjustment screw is used to limit the travel of the throttle

valve inside the carburetor. Turn the adjustment screw until the point

is flush to the bottom of the rotary lever, this will be the throttle stop

position. The spring is already installed on the carburetor and should

be left in place. The spring provides the necessary tension along the

length of the throttle lever axle to prevent wearing of the shaft prema-

turely. Install the carburetor to the engine crankcase using the screws

and gaskets included with the engine with the primer bubble facing

rearward and the fuel fittings on top.

Idle Screw, position flush to

bottom of throttle lever.

Step 58 Fuel Lines

Of the three lines to the fuel tank, both the primer

return line and the atmosphere line can use the 1/8”

ID fuel line. The fuel pickup line on the Z231H en-

gine should use the same 1/8” ID fuel line but use the

larger 3/16” ID fuel line on the Z260H engine. The

atmosphere line should run from the top of the fuel

tank, upward and looped near the top of the vertical

frame and then routed and tied to one of the landing

gear spacers, making sure that the fuel line extends

1/4” past the plastic struts.

Fuel Pickup Line

Primer Return Line

Atmosphere

Line

Tygon fuel line

not included.

Содержание Gas SE







































Результаты поиска

Содержание Gas SE

Отзывы:

Predator Gas SE, Инструкция по эксплуатации, Страница: 24 / 38

Результаты поиска

Содержание Gas SE

Отзывы: