Polaris 2010 OUTLAW 450 MXR Скачать руководство пользователя

Страница: 104 / 212

100

Maintenance

Engine Oil Change

Always change the oil at the intervals outlined in the Periodic Maintenance Chart beginning

on page 87. Change the oil more frequently on vehicles subjected to severe use.

IMPORTANT

: Perform the initial break-in oil change after the first three hours of operation. Always

change both oil filters and clean the oil screens whenever changing oil.

Before beginning the oil change procedure, read through the entire procedure. Be prepared to

complete the procedure entirely. Do not allow the vehicle to be without oil and filter over-

night. Always replace the oil and filters within a few hours of draining the oil.

NOTICE:

If the ATV is left without oil in the system for extended periods, the oil pump may lose its

prime, which could result in engine damage.

Содержание 2010 OUTLAW 450 MXR





















































































































































































































Результаты поиска

Содержание 2010 OUTLAW 450 MXR

Отзывы:

Похожие инструкции для 2010 OUTLAW 450 MXR

Бренды по названию

Популярные бренды

Polaris 2010 OUTLAW 450 MXR, Руководство пользователя

Результаты поиска

Содержание 2010 OUTLAW 450 MXR

Отзывы:

Похожие инструкции для 2010 OUTLAW 450 MXR

Бренды по названию

Популярные бренды