Polaris 2010 OUTLAW 450 MXR Скачать руководство пользователя

Страница: 159 / 212

155

Maintenance

Rear Suspension

The rear suspension spring preload, shock rebound damping

and shock compression damping may be adjusted to suit

different riding conditions and operator weight.

Spring Preload

1. Raise and safely support the rear of the vehicle off the

ground to allow the suspension to fully extend.

2. Loosen the jam nut and back it away from the adjusting

ring.

3. Turn the adjusting ring to the left (1) to increase pre-

load. Turn the ring to the right (2) to decrease preload.

See Suspension Settings on page 152.

4. Tighten the jam nut firmly against the adjuster ring.

Jam

Nut

Adjusting

Ring

Содержание 2010 OUTLAW 450 MXR





















































































































































































































Результаты поиска

Содержание 2010 OUTLAW 450 MXR

Отзывы:

Похожие инструкции для 2010 OUTLAW 450 MXR

Бренды по названию

Популярные бренды

Polaris 2010 OUTLAW 450 MXR, Руководство пользователя

Результаты поиска

Содержание 2010 OUTLAW 450 MXR

Отзывы:

Похожие инструкции для 2010 OUTLAW 450 MXR

Бренды по названию

Популярные бренды