Polaris 2010 OUTLAW 450 MXR Скачать руководство пользователя страница 136

Страница: 136 / 212

132

Maintenance

Battery Charging (Sealed Battery)

On a sealed battery, the sealing strip cannot be removed. Use a voltmeter or multimeter to

measure DC voltage. A fully charged battery will register 12.8 V or higher. If the voltage is

less than 12.8 volts, recharge the battery.

WARNING!

An overheated battery could explode, causing severe injury or death. Always watch

charging times carefully. Stop charging if the battery becomes very warm to the touch. Allow it to cool

before resuming charging.

The battery may be recharged without

removing it from the vehicle. Attach cables

in the following order:
1. Attach the positive (+) cable clamp to

the solenoid lead (directly wired to the

battery).

2. Attach the negative (-) cable clamp to

the negative (-) battery terminal.

2. Negative (-)

Terminal

1. Solenoid Lead

Содержание 2010 OUTLAW 450 MXR





















































































































































































































Результаты поиска

Содержание 2010 OUTLAW 450 MXR

Отзывы:

Бренды по названию

Популярные бренды

Polaris 2010 OUTLAW 450 MXR, Руководство пользователя

Результаты поиска

Содержание 2010 OUTLAW 450 MXR

Отзывы:

Бренды по названию

Популярные бренды