Polaris 2010 OUTLAW 450 MXR страница 57 Скачать руководство пользователя

Страница: 57 / 212

Features and Controls

Manual Shift

Shifting Gears

Always allow a cold engine to warm up

before shifting gears.
1. When starting from a stopped position,

place the transmission in neutral.

2. Squeeze and hold the brake lever. Do

not apply throttle.

3. Squeeze the clutch lever to disengage

the clutch.

4. Depress the gear shift pedal one full

stroke to shift into first gear.

5. Release the brake lever.
6. Gradually squeeze the throttle lever

while slowly releasing the clutch lever.

7. As engine speed (RPM) increases in

first gear, simultaneously release the

throttle, disengage the clutch and shift

to second gear by raising the gear shift

pedal one full stroke. Repeat this proce-

dure to progressively upshift to addi-

tional gears. Use the same procedure to

downshift.

WARNING!

Shifting without releasing the throttle

and disengaging the clutch could cause loss of

control or vehicle overturn. Always release the

throttle and fully squeeze the clutch lever while

shifting gears.

Содержание 2010 OUTLAW 450 MXR





















































































































































































































Результаты поиска

Содержание 2010 OUTLAW 450 MXR

Отзывы:

Похожие инструкции для 2010 OUTLAW 450 MXR

Бренды по названию

Популярные бренды

Polaris 2010 OUTLAW 450 MXR, Руководство пользователя

Результаты поиска

Содержание 2010 OUTLAW 450 MXR

Отзывы:

Похожие инструкции для 2010 OUTLAW 450 MXR

Бренды по названию

Популярные бренды