Polaris 2010 OUTLAW 450 MXR Скачать руководство пользователя страница 89

Страница: 89 / 212

Emission Control Systems

Noise Emission Control System

Do not modify the engine, intake or exhaust components, as doing so may affect compliance

with U.S.A. EPA noise control requirements (40 CFR 205) and local noise level require-

ments.

Operation on Public Lands in the U.S.A.

Your Polaris vehicle has a spark arrestor that was tested and qualified to be in accordance

with the USFS standard 5100-1c. Federal law requires that this spark arrestor be installed

and functional when the vehicle is operated on public lands.
Operation of off-road vehicles on public lands in the U.S.A. is regulated by 43 CFR 420.

Violations are subject to monetary penalties. Federal regulations can be viewed online at

www.gpoaccess.gov/ecfr/.

Crankcase Emission Control System

This engine is equipped with a closed crankcase system. Blow-by gases are forced back to

the combustion chamber by the intake system. All exhaust gases exit through the exhaust

system.

Содержание 2010 OUTLAW 450 MXR





















































































































































































































Результаты поиска

Содержание 2010 OUTLAW 450 MXR

Отзывы:

Бренды по названию

Популярные бренды

Polaris 2010 OUTLAW 450 MXR, Руководство пользователя

Результаты поиска

Содержание 2010 OUTLAW 450 MXR

Отзывы:

Бренды по названию

Популярные бренды